June 19th, 2020. The low-cost, low-power and long-distance cattle collar developed in the EU H2020 WAZIUP project has been identified by the European Commission's Innovation Radar! See more information at the end of this page.
-
NEW-Jan21 To provide support for next 64-bit OS the low-level SPI library on the Raspberry gateway has moved from Libelium's
arduPilib to Gordon'swiringPilib becausearduPirelies heavily on direct memory accesses that are difficult to port. The main reason for 64-bit OS is to prepare the whole low-cost Raspberry-based gateway to embed advance AI frameworks that are mostly based on 64-bit OS. See README. -
NEW-Nov20 To support the new SX126X and SX128X LoRa chips, we updated and added Arduino ProMini PCBs to easily connect NiceRF SX1262 and NiceRF SX1280 modules. These modules have same size than the HopeRF RFM95W for SX1276.
-
NEW-Oct20 The low-level radio communication library has moved to the SX12XX LoRa library from Stuart Robinson in order to build devices and gateways with SX126X, SX127X and SX128X LoRa chip. The default gateway program is compiled for an SX127X based module using the SX12XX library. This is a major move to provide support for the most recent LoRa chips including those for 2.4GHz LoRa. See README.
- The current SD card image (Debian Buster) has everything you need! zipped SD card image. See installation section
- Use the single-channel gateway for LoRaWAN-like communication (including downlink) with LoRa 2.4GHz. Upload to TTN or ChirpStack network servers. See README
- Use the single-channel gateway for limited LoRaWAN (including downlink and OTAA feature) on the 433MHz band for devices with our modified LMIC
- The single-channel gateway now also provides LoRaWAN downlink and OTAA features for devices with our modified LMIC. See updated README
- Includes support of the open-source ChirpStack LoRaWAN Network Server, see README
- Support of multi-channel RPI SX1301 LoRaWAN gateway: benefit from the open, versatile, multi-cloud Low-cost LoRa IoT framework with the flexibility and scalability of a multi-channel LoRaWAN gateway, see README
- We have a new online Arduino-Sensor-LoRa tutorial and here is the direct link to the LoRa part
- Read the Low-cost-LoRa-device leaflet
- Read the Low-cost-LoRa-GW leaflet
- Look at the Low-cost-LoRa-GW web admin interface tutorial. For most end-users, the web admin interface is sufficient to configure and manage the gateway. For instance, to configure a new gateway, it is recommended to use the web admin interface to update the gateway software and to run the basic configuration procedure as described here
- The rest of this README file contains additional information to better understand the proposed low-cost IoT framework.
In order to facilitate connection between an Arduino board or a RaspberryPI and the well-known RFM95W (SX1276) LoRa radio module, we developed simple PCBs for Arduino ProMini, Arduino Nano and RaspberryPI and make them freely available.
The first PCB is a simple RFM95W breakout with header pins for both the Raspberry (mainly to make a gateway) and Arduino boards. The RFM95W breakout initially designed for the HopeRF RFM95W (referred to as old RFM95W breakout) can actually also host the recent NiceRF SX1262 as both radio modules have similar pinout. However, we updated the old RFM95W breakout's wiring to also expose DIO2 and DIO1 on the Raspberry header to better support the NiceRF SX1262 module (DIO2 location on the RFM95W is the BUSY pin on the NiceRF SX1262 and DIO1 pin is used for RX/TX done interrupt on the NiceRF SX1262 instead of the DIO0 pin on the RFM95W). BUSY pin is needed for the SX126X so if you are using the old RFM95W breakout you need to solder a wire. Our modified communication library does not need DIO1 pin. When updating the RFM95W breakout we also added a 4-pin header to easily connect a small OLED screen to a Raspberry using the I2C bus (SCL and SDA pin).
We also made a variant to support the NiceRF SX1280 module which provides LoRa modulation on the 2.4GHz band (I really don't know why the SX1280 did not use the same pinout than the SX1262 which is similar to the RFM95W!). All these breakout PCBs are illustrated in the following figure.
These PCBs can therefore be connected to the GPIO header row of the Raspberry as shown below. Pins on the Raspberry for RST, CS (or NSS), DIO2/BUSY and DIO1 are shown.
These breakouts can also be used for Arduino boards as it will be explained in Section connect a radio module to your end-device and illustrated below. On the breakout's Arduino header, you can connect RFM95's DIO0 to a digital pin of your Arduino if you want to use another communication library that needs this pin. For NiceRF SX1262 and NiceRF SX1280 you can get BUSY and DIO1 pins from the Raspberry header with the updated design. BUSY pin is needed but our modified communication library does not need DIO1 pin.
However, for Arduino, it is more convenient to use our dedicated Arduino Nano/ProMini PCBs illustrated below. The PCB for Arduino Nano is mainly intended for teaching/training purpose as the Nano is not energy-efficient enough for real deployment. However its main advantage is to avoid the need of an external FTDI breakout cable to program it. It has not been updated for a while and we are not really maintaining it anymore. You can find in the PCB folder the EAGLE schematic file (NanoLoRaBreakout_2019-05-14.sch) if you want to modify the design yourself.
The PCB for the Arduino ProMini (3.3v, 8MHz version) can be used for prototyping and even integration purpose. Beware that A4 and A5 (which are usually SDA and SCL pin of the I2C bus) are not connected on the PCB. If you need to use them, use these 2 pins from the Arduino board itself. The PCB for the Arduino ProMini has been updated several times. The last version is v3 for both RFM95W and NiceRF SX1262 and v2 for NiceRF SX1280.
All the PCBs have footprint for an SMA connector or uFl. Both Nano and ProMini PCBs have replicated rows for all the pins. They also have extra VCC and GND rails. They also have 4 solder pads that can be soldered together if you want to connect various DIO pins. Some of these pads are by default connected. If you want to use the connected Arduino pins for other purposes, just cut the wire between the pads with a cutter and test for discontinuity.
- for RFM95W. Connected by default: DIO0 to D2, DIO1 to D3, RST to D4. Not connected by default: DIO2 to D5
- for NiceRF SX1262. Connected by default: DIO1 to D3, RST to D4. Not connected by default: BUSY to D5
- for NiceRF SX1280. Connected by default: DIO1 to D2, BUSY to D3 and RST to D4. Not connected by default: DIO2 to D5
Our modified communication library makes wiring a bit easier because only CS, MISO, MOSI, SCK, BUSY (SX126X and SX128X only) and RST are needed. However on the PCBs, DIOs pins are available to use other libraries (for LMIC stack for instance). We also indicate clearly which pin of the LoRa module you need to solder on the PCB (for instance MOSI>). As you can see on the picture, you can directly solder the Arduino board on the PCB, or, as we did, use intermediate headers so that the Arduino board can be easily plugged and removed.
You can download all the Gerber zipped archive and view them on an online Gerber viewer.
- RFM95W/NiceRF SX1262 breakout zipped Gerber archive, 2 layer board of 29x37mm .zip
- NiceRF SX1280 breakout zipped Gerber archive, 2 layer board of 29x37mm .zip
- Arduino Nano v2 PCB for RFM95W zipped Gerber archive, 2 layer board of 30x81mm .zip
- Arduino ProMini v3 PCB for RFM95W/NiceRF SX1262 zipped Gerber archive, 2 layer board of 30x77mm .zip
- Arduino ProMini v2 PCB for NiceRF SX1280 zipped Gerber archive, 2 layer board of 30x77mm .zip
You can easily make them produced on many online PCB manufacturers. Usually, you just need to provide the zip archive and both size and number of layers are detected. You can dramatically decrease the price by using "panelize" option. As you can see on the pictures, we use 3x2 for the RFM95 breakout and 3x1 for both the Nano and ProMini PCBs. For instance, we ordered them from JLCPCB and the cost of 10 panels (i.e. 60 RFM95W breakout or 30 Nano/ProMini breakout) is about $4!
1 online tutorial
3 tutorial videos on YouTube: video of all the steps to build the whole framework from scratch
- Build your low-cost, long-range IoT device with WAZIUP
- Extreme low-cost & low-power LoRa IoT for real-world deployment
- Build your low-cost LoRa gateway with WAZIUP
1 live demo video on YouTube: setting up a gateway in less than 5 mins to upload data to various clouds
Go to https://github.com/CongducPham/tutorials for all tutorials and particularly look for:
- Low-cost-LoRa-GW-outdoor
- Low-cost-LoRa-GW leaflet
- Low-cost-LoRa-device leaflet
- Low-cost-LoRa-IoT-step-by-step tutorial
- Low-cost-LoRa-GW-step-by-step tutorial
- Low-cost-LoRa-GW web admin interface tutorial
- Low-cost-LoRa-IoT-antennaCable tutorial
Look also at our FAQ!
Also consult the following web page: http://cpham.perso.univ-pau.fr/LORA/RPIgateway.html.
- NEW Support of 64-bit OS to better embed AI frameworks
- NEW The low-level radio communication library has moved to the SX12XX LoRa library from Stuart Robinson in order to build devices and gateways with SX126X, SX127X and SX128X LoRa chip.
- NEW The single-channel gateway now also provides LoRaWAN downlink and OTAA features
- see README
- NEW Integration and easy configuration of the open-source ChirpStack Network Server as local Network Server
- see README
- NEW Support of multi-channel RPI SX1301 LoRaWAN gateway
- benefit from the open, versatile, multi-cloud Low-cost LoRa IoT framework with the flexibility and scalability of a multi-channel LoRaWAN gateway
- see README
- support of LoRaWAN and connection to LoRaWAN cloud (e.g. TTN platform)
- simple, flexible and generic cloud management approach
- README
- look at the provided cloud script examples to see how IoT clouds such as TTN, ThingSpeak, GroveStreams, MQTT,... are supported
- a cloud script can be used to generalize the upload of data using SMS, ftp, file, MQTT, Node-Red flow,...
- remote access to your gateway from anywhere:
remot3.it,ngrok - a simple, user-friendly web admin interface to configure and update your gateway
- open a browser and go to http://
gw_ip_address/admin - README
- Tutorial
raspap-webguifrom https://github.com/billz/raspap-webgui has been integrated and can be accessed at http://gw_ip_address/raspap-webgui. When the gateway is configured as a WiFi client,raspap-webguiis especially useful to dynamically discover and configure additional WiFi networks. Read this section prior to useraspap-webgui.
- open a browser and go to http://
- a NoSQL MongoDB database stores received data for local/edge processing. See here for more information on the local MongoDB structure.
- the gateway acts as the WiFi access-point. The SSID is WAZIUP_PI_GW_XXXXXXXXXX where XXXXXXXXXX is the last 6 hex bytes of gateway ID: WAZIUP_PI_GW_B827EB27F90F for instance. It has IP address 192.168.200.1 and will lease IP addresses in the range of 192.168.200.100 and 192.168.200.120.
- there is an Apache web server with basic PHP forms to visualize graphically the received data of the MongoDB with any web browser. Just connect to http://192.168.200.1 with a web browser (could be from a smartphone) to get the graphic visualization of the data stored in the gateway's MongoDB database.
- by default, incoming data are uploaded to our LoRa ThingSpeak test channel
- works out-of-the-box with the Arduino_LoRa_Simple_temp sketch
If you want to manually connect a LoRa radio module to the Raspberry's GPIO header, just connect the corresponding SPI pin (MOSI, MISO, CLK, CS) and the reset (RST) pin.
RPI Radio module
GND pin 25----------GND (ground in)
3V3 pin 17----------3.3V (3.3V in)
GPIO4 pin 7----------RST (Reset)
CS/CE0 pin 24----------NSS (CS chip select in)
SCK pin 23----------SCK (SPI clock in)
MOSI pin 19----------MOSI (SPI Data in)
MISO pin 21----------MISO (SPI Data out)
You can have a look at the "Low-cost-LoRa-GW-step-by-step" tutorial in our tutorial repository https://github.com/CongducPham/tutorials.
Or you can of course use our RFM95W/NiceRF SX1262 and NiceRF SX1280 breakouts that can be directly connected to the Raspberry GPIO header. Look also at our Low-cost-LoRa-GW-outdoor tutorial to build an outdoor gateway.
The full, latest distribution of the low-cost gateway is available in the gw_full_latest folder of the github repository: https://github.com/CongducPham/LowCostLoRaGw. It contains all the gateway control and post-processing software.
However, the simplest and recommended way to install a new gateway is to use our zipped SD card image based on the Buster Raspbian OS and perform a new install of the gateway from this image. In this way you don't need to install the various additional packages that are required (as explained in an additional README describing all manual installation steps if you want to install from scratch). Once you have burnt the SD image on a 8GB (minimum) SD card, insert it in your Raspberry and power it.
The distribution supports all RPI models including the last RPI4. There is out-of-the-box WiFi support for RPI4B/3B/3B+ and RPI0W. For RPI1 and RPI2 see here for modifications to support some WiFi dongles.
Download our zipped SD card image. The current image has everything you need including:
- support for all RPI models including the last RPI4 as well. We however recommend the 3B version unless you need to run other applications on the RPI otherwise both 3B+/4 are much more power consuming and heat a lot more.
- pre-installed open-source ChirpStack LoRaWAN Network Server
- pre-installed Semtech's
lora_pkt_fwdfor multi-channel gteway - pre-installed
remot3.itandanydesktools for remote access - the simple gateway web admin interface for easy configuration and management
mosquitto-clientspackage installed to havemosquitto_pubandmosquitto_subcommands (v1.5.7)- Node-Red v1.0.3, Node.js v10.15.2 and
npm5.8.0 withnode-red-contrib-thingspeak42installed - a ready-to-use Node-Red flow to show how received data can be uploaded to MQTT brokers and ThingSpeak
- MongoDB v3.0.14
Simply unzip the file and burn the ISO file to an SD card. Use an SD card of a minimum of 8GB. Take also a class 10 (it is more than recommended!). If you have bigger SD card, e.g. 16GB, then after boot, use raspi-config (see tutorial here) to resize the partition in order to use the extra space available (you will need to reboot but raspi-config will ask you for that). You can use df -h to verify that you have more space after reboot.
You can look at various tutorials on how to burn an image to an SD card. There is one here from raspberrypi.org and here from elinux.org. We use a Mac to do so and this is our preferred solution. The Linux version is not very different. The Balena Etcher tool is also very nice and you don't even need to unzip the SD card image. We also use that solution extensively.
Important notice: the LoRa gateway program starts automatically when the Raspberry is powered on.
You can try your gateway right away now by building your end-device and jump directly to this section.
If you want to connect (ssh) to the gateway and perform update procedure, read the rest of the section.
The SD card image defines a pi user:
- login: pi
- password: loragateway
With the default gateway configuration, the gateway acts as a WiFi access point. If you see the WiFi network WAZIUP_PI_GW_XXXXXXXXXX then connect to this WiFi network. The WiFi password is loragateway. It is strongly advise to change this WiFi password. The address of the Raspberry is then 192.168.200.1. Note that it is very convenient to use a smartphone or a tablet to connect to your gateway with ssh. On iOS we tested Termius and on Android we tested JuiceSSH.
If you see no WiFi access point (e.g. RP1/RPI2/RPI0 without WiFi dongle), then plug your Raspberry into a DHCP-enabled box/router/network to get an IP address or shared your laptop internet connection to make your laptop acting as a DHCP server. On a Mac, there is a very simple solution here. For Windows, you can follow this tutorial or this one. You can then use Angry IP Scanner available on Windows/Mac/Linux/Android to determine the assigned IP address for the Raspberry.
We will use in this example 192.168.2.8 for the gateway address (DHCP option in order to have Internet access from the Raspberry)
> ssh [email protected]
[email protected]'s password:
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
Last login: Thu Aug 4 18:04:41 2016
For the Raspberry Zero, our SD card image set the RPI in access point mode. However, when in access-point mode, Ethernet over USB with dtoverlay=dwc2 in /boot/config.txt and modules-load=dwc2,g_ether in /boot/cmdline.txt is not working. As the usage of the Raspberry Zero is mainly with Internet connection through a cellular network (using for instance the LORANGA board from La Fabrica Alegre) the easiest way to have Internet through Ethernet sharing with our SD card image is to use a USB-Ethernet adapter that will add an eth0 interface on the RPI0. These USB-Ethernet adapter are quite cheap and are really useful on the RPI0 as you can then connect it to a DHCP-enabled router/box just like the other RPI boards. Alternatively, you can set your gateway as a WiFi client to connect to an existing WiFi network, see here.
Once you have your SD card flashed with our image, to get directly to the full, latest gateway version, you can either use (i) the web admin interface, or (ii) the provided update script to be run from the gateway, or (iii) download (git clone) the whole repository and copy the entire content of the gw_full_latest folder on your Raspberry, in a folder named lora_gateway or, (iv) get only (svn checkout) the gw_full_latest folder in a folder named lora_gateway. Option (i) is recommended and simple while (ii) is basically an automatization of option (iii) in command line mode. Both options (i) and (ii) however need Internet connectivity on the gateway while option (iii) and (iv) can be done on a computer prior to copy the files on the Raspberry.
It is the recommended option but the Raspberry must have Internet connection.
Choose the Gateway Update menu on the left. Then, if you install a brand new gateway with our SD card image, use New installation. For future updates, use Full update.
After New installation or Full update, run Basic config.
When using the web interface, you don't need to perform the manual Configuring your gateway after update step below.
It is also recommended to run Update web admin interface to update the web interface to the last version, after New installation or Full update.
Then reboot.
The full LoRa gateway with post-processing stage starts automatically when the Raspberry is powered on. By default, incoming data are uploaded to our LoRa ThingSpeak test channel. It will work out-of-the-box with the Arduino_LoRa_Simple_temp sketch.
If your gateway has Internet connectivity (DHCP with Internet sharing on your laptop for instance), you can use our update_gw.sh script. Even if the SD card image has a recent version of the gateway software with the update_gw.sh script in the lora_gateway/scripts folder it is safer to get the latest version of this script. Simply do:
> cd /home/pi
> wget https://raw.githubusercontent.com/CongducPham/LowCostLoRaGw/master/gw_full_latest/scripts/update_gw.sh
> chmod +x update_gw.sh
> ./update_gw.sh
Note that if you have customized configuration files (i.e. key_*, gateway_conf.json, clouds.json and radio.makefile) in the existing /home/pi/lora_gateway folder, then update_gw.sh will preserve all these configuration files. As the repository does not have a gateway_id.txt file, it will also preserve your gateway id.
Otherwise, if it is really the first time you install the gateway, then you can delete the lora_gateway folder before running the script:
> rm -rf lora_gateway
> ./update_gw.sh
This upgrade solution can be done on the Raspberry if it has Internet connectivity or on your laptop which is assumed to have Internet connectivity. If you don't have git installed on your laptop, you have to install it first. Then get all the repository:
> cd /home/pi
> git clone https://github.com/CongducPham/LowCostLoRaGw.git
You will get the entire repository:
pi@raspberrypi:~ $ ls -l LowCostLoRaGw/
total 32
drwxr-xr-x 7 pi pi 4096 Apr 1 15:38 Arduino
-rw-r--r-- 1 pi pi 15522 Apr 1 15:38 README.md
drwxr-xr-x 2 pi pi 4096 Apr 1 15:38 gw_full_latest
drwxr-xr-x 2 pi pi 4096 Apr 1 15:38 tutorials
Create a folder named lora_gateway (or if you already have one, then delete all its content) then copy all the files of the LowCostLoRaGw/gw_full_latest folder in it.
> mkdir lora_gateway
> cd lora_gateway
> cp -R ../LowCostLoRaGw/gw_full_latest/* .
Or if you want to "move" the LowCostLoRaGw/gw_full_latest folder, simply do (without creating the lora_gateway folder before):
> mv LowCostLoRaGw/gw_full_latest ./lora_gateway
If you download the repository from your laptop, then rename gw_full_latest into lora_gateway and copy the entire lora_gateway folder into the Raspberry using scp for instance. In the example below, the laptop has wired Internet connectivity and use the gateway's advertised WiFi to connect to the gateway. Therefore the IP address of the gateway is 192.168.200.1.
> scp -r lora_gateway [email protected]:/home/pi
If you don't want to use/install git, use your laptop to get the .zip file of the entire github with the "Clone or download" option, unzip the package, rename the gw_full_latest folder as lora_gateway and perform the scp command.
This upgrade solution can be done on the Raspberry if it has Internet connectivity or on your laptop which is assumed to have Internet connectivity. If you don't have svn installed on your laptop, you have to install it first. Then get only the gateway part:
> cd /home/pi
> svn checkout https://github.com/CongducPham/LowCostLoRaGw/trunk/gw_full_latest lora_gateway
That will create the lora_gateway folder and get all the file of (GitHub) LowCostLoRaGw/gw_full_latest in it.
To install svn on the Raspberry:
> sudo apt-get install subversion
Here, again, you can do all these steps on your laptop and then use scp to copy to the Raspberry.
After gateway update with option (ii), (iii) or (iv), you need to configure your new gateway with basic_config_gw.sh, that mainly assigns the gateway id so that it is uniquely identified (the gateway's WiFi access point SSID is based on that gateway id for instance). The gateway id will be the last 6 bytes of the Rapberry eth0 MAC address (or wlan0 on an RPI0W without Ethernet adapter) and the configuration script will extract this information for you. There is an additional script called test_gwid.sh in the script folder to test whether the gateway id can be easily determined. In the scripts folder, simply run test_gwid.sh:
> cd /home/pi/lora_gateway/scripts
> ./test_gwid.sh
Detecting gw id as 0000B827EBBEDA21
If you don't see something similar to 0000B827EBBEDA21 (8 bytes in hex format) then you have to explicitly provide the last 6 bytes of the gw id to basic_config_gw.sh. Otherwise, in the scripts folder, simply run basic_config_gw.sh to automatically configure your gateway.
> cd /home/pi/lora_gateway/scripts
> ./basic_config_gw.sh
or
> ./basic_config_gw.sh B827EBBEDA21
If you need more advanced configuration, then run config_gw.sh as described here. However, basic_config_gw.sh should be sufficient for most of the cases. The script also compile the low-level gateway program corresponding to you Raspberry model. After configuration, reboot your Raspberry.
By default gateway_conf.json configures the gateway with a simple behavior: LoRa mode 1 (BW125SF12), no DHT sensor in gateway (so no MongoDB for DHT sensor), no downlink, no AES, no raw mode. clouds.json enables only the ThingSpeak demo channel (even the local MongoDB storage is disabled). You can customize your gateway later when you have more cloud accounts and when you know better what features you want to enable.
The LoRa gateway starts automatically when RPI is powered on. Then use cmd.sh to execute the main operations on the gateway as described here.
To have an end-device, you have to connect a LoRa radio module to an Arduino board. Just connect the corresponding SPI pin (MOSI, MISO, CLK, CS/SS) and the RST pin. On the Uno, Pro Mini, Mini, Nano, Teensy the mapping is as follows:
Arduino Radio module
GND----------GND (ground in)
3V3----------3.3V (3.3V in)
SS pin D10----------NSS (CS chip select in)
SCK pin D13----------SCK (SPI clock in)
MOSI pin D11----------MOSI (SPI Data in)
MISO pin D12----------MISO (SPI Data out)
D4----------RST (Reset)
For the Nano and the ProMini, you can of course use our Nano/ProMini PCBs that makes connection to an RFM95W/NiceRF SX1262 and NiceRF SX1280 radio straightforward.
On the MEGA, the SPI pin are as follows: 50 (MISO), 51 (MOSI), 52 (SCK). Starting from November 3rd, 2017, the CS pin is always pin number 10 on Arduino and Teensy boards. You can have a look at the Low-cost-LoRa-IoT-step-by-step tutorial in the tutorial repository https://github.com/CongducPham/tutorials.
There is an important issue regarding the radio modules. The Semtech SX1272/76 has actually 2 lines of RF power amplification (PA): a high efficiency PA up to 14dBm (RFO) and a high power PA up to 20dBm (PA_BOOST).
However even if the SX1272/76 chip has the PA_BOOST and the 20dBm features, not all radio modules (integrating these SX1272/76) do have the appropriate wiring and circuits to enable these features: it depends on the choice of the reference design that itself is guided by the main intended frequency band usage, and sometimes also by the target country's regulations (such as maximum transmitted power). So you have to check with the datasheet whether your radio module has PA_BOOST (usually check whether the PA_BOOST pin is wired) and 20dBm capability. Some other radio modules only wire the PA_BOOST and not the RFO resulting in very bad range when trying to use the RFO mode. In this case, you have to explicitly indicate that PA_BOOST is used.
All the examples using the SX127X radio module start with:
// IMPORTANT
///////////////////////////////////////////////////////////////////////////////////////////////////////////
//
// uncomment if your radio is an HopeRF RFM92W, HopeRF RFM95W, Modtronix inAir9B, NiceRF1276
// or you known from the circuit diagram that output use the PABOOST line instead of the RFO line
//#define PABOOST
///////////////////////////////////////////////////////////////////////////////////////////////////////////
Uncomment PABOOST if you have a HopeRF RFM92W or RFM95W or RFM96W, or a Modtronix inAir9B (if inAir9, leave commented) or a NiceRF1276. If you have another non listed radio module, try first by leaving PABOOST commented, then see whether the packet reception is correct with a reasonably high SNR (such as 6 to 10 dB) at some meters of the gateway. If not, then try with PABOOST uncommented.
As suggested by some people, we provide here a simple Ping-Pong program to upload on an Arduino board. First, install the Arduino IDE. You can use the latest one (we tested with 1.8.6). There have been some issues with the Arduino AVR board library version (some time ago, libraries above 1.6.11 showed some compilation issues because of changes in the GCC AVR compiler) but it seems that these issues have been solved. So now, you can also use the latest Arduino AVR board library (1.6.22 at time writing, included with Arduino 1.8.6 IDE). Then, in your sketch folder, copy the content of the Arduino folder of the distribution.
Run the gateway with:
> sudo ./lora_gateway
With the Arduino IDE, open the Arduino_LoRa_Ping_Pong sketch (or the Arduino_LoRa_SX12XX_Ping_Pong_LCD if you move to the SX12XX library which is advised because Arduino_LoRa_Ping_Pong will not be maintained anymore)compile it and upload to an Arduino board. Check your radio module first, see Connect a radio module to your end-device above.
The end-device runs in LoRa mode 1 and has address 8. Open the Serial Monitor (38400 bauds) to see the output of the Arduino. It will send "Ping" to the gateway by requesting an ACK every 10s. If the ACK is received then it will display "Pong received from gateway!" otherwise it displays "No Pong from gw!". There is a version using an OLED display, Arduino_LoRa_Ping_Pong_LCD, that can be compiled for the Heltec ESP32 WiFi LoRa OLED board or a regular Arduino Pro Mini board (we use a Pro Mini or a Nano) with a 0.96inch OLED I2C display. Such device can be used as a very convenient simple range tester.
Note that in most operational scenarios, requesting ACK from the gateway is costly. Look at the next examples to see how we usually send data without requesting ACK.
Notice for low-cost/clone Arduino boards. If you get a low-cost Arduino board, such as those sold by most of Chinese manufacturer, the USB connectivity is probably based on the CH340 or CH341. To make your low-cost Arduino visible to your Arduino IDE, you need the specific driver. Sparkfun has a nice web page explaning serial connection to Arduino at https://learn.sparkfun.com/tutorials/serial-basic-hookup-guide. Links to CH341 drivers for Windows, Linux and MacOs can be found in the "Drivers If You Need Them" section. There is also this link http://sparks.gogo.co.nz/ch340.html. For MacOS, you can also look at http://www.mblock.cc/posts/run-makeblock-ch340-ch341-on-mac-os-sierra which works for MacOS up to Sierra. For MacOS user that have the previous version of CH34x drivers and encountering kernel panic with Sierra, don't forget to delete previous driver installation: sudo rm -rf /System/Library/Extensions/usb.kext.
See the video here.
First, install the Arduino IDE. You can use the latest one (we tested with 1.8.3). But then, check (see the board manager) that the Arduino AVR board library is not above 1.6.11 as there might be some compilation issues because of the change of the GCC AVR compiler. Then, in your sketch folder, copy the content of the Arduino folder of the distribution.
With the Arduino IDE, open the Arduino_LoRa_Simple_temp sketch (or the Arduino_LoRa_SX12XX_Simple_temp if you move to the SX12XX library which is advised because Arduino_LoRa_Simple_temp will not be maintained anymore), compile it and upload to an Arduino board. Check your radio module first, see Connect a radio module to your end-device above.
The end-device runs in LoRa mode 1 and has address 6. It will send data to the gateway.
The default configuration uses an application key filter set to [5, 6, 7, 8].
Use a temperature sensor (e.g. LM35DZ) and plugged in pin A0 (analog 0). You can use a power pin to power your temperature sensor if you are not concerned about power saving. Otherwise, you can use digital 9 (the sketch set this pin HIGH when reading value, then sets it back to LOW) and activate low power mode (uncomment #define LOW_POWER), see below.
For low-power applications the Pro Mini from Sparkfun is certainly a good choice. This board can be either in the 5V or 3.3V version. With the Pro Mini, it is better to really use the 3.3V version running at 8MHz as power consumption will be reduced. Power for the radio module can be obtained from the VCC pin which is powered in 3.3v when USB power is used or when unregulated power is connected to the RAW pin. If you power your Pro Mini with the RAW pin you can use for instance 4 AA batteries to get 6V. If you use a rechargeable battery you can easily find 3.7V Li-Ion packs. In this case, you can inject directly into the VCC pin but make sure that you've unsoldered the power isolation jumper (Sparkfun Pro Mini) or removed the voltage regulator, see Pro Mini schematic on the Arduino web page. To greatly save power, you should remove the power led.
The current low-power version for Arduino board use the RocketScream Low Power library (https://github.com/rocketscream/Low-Power) and can support most Arduino platforms although the Pro Mini platform will probably exhibit the best energy saving (we measured 54uA current in sleep mode with the power led removed and 12uA when the voltage regulator is removed). You can buid the low-power version by uncommenting the LOW_POWER compilation define statement. Then set int idlePeriodInMin = 10; to the number of minutes between 2 wake-up. By default it is 10 minutes. There are good web site describing low-power optimization for the pro Mini: http://www.home-automation-community.com/arduino-low-power-how-to-run-atmega328p-for-a-year-on-coin-cell-battery/ or https://andreasrohner.at/posts/Electronics/How-to-modify-an-Arduino-Pro-Mini-clone-for-low-power-consumption/.
For the special case of Teensy boards (LC/31/32/35/36), the power saving mode uses the excellent work of Collin Duffy with the Snooze library included by the Teensyduino package. You can upgrade the Snooze library from the github https://github.com/duff2013/Snooze as version 6 is required to handle the new Teensy 35/36 boards. With the Teensy, you can further use the HIBERNATE mode by uncommenting LOW_POWER_HIBERNATE in the temperature example.
For the special of the Arduino Zero, waking up the board from deep sleep mode is done with the RTC. Therefore the RTCZero library from https://github.com/arduino-libraries/RTCZero is used and you need to install it before being able to compile the example for the Arduino Zero.
Depending on the sensor type, the computation to get the real temperature may be changed accordingly. Here is the instruction for the LM35DZ: http://www.instructables.com/id/ARDUINO-TEMPERATURE-SENSOR-LM35/
The default configuration also use the EEPROM to store the last packet sequence number in order to get it back when the sensor is restarted/rebooted. If you want to restart with a packet sequence number of 0, just comment the line #define WITH_EEPROM
Once flashed, the Arduino temperature sensor will send to the gateway the following message \!#3#TC/20.4 (TC is used as the nomenclature code and 20.4 is the measured temperature so you may not have the same value) prefixed by the application key every 10 minutes (with some randomization interval). This will trigger at the processing stage of the gateway the logging on the default ThinkSpeak channel (the test channel we provide) in field 3. At the gateway, 20.4 will be recorded on the provided ThingSpeak test channel in field 3 of the channel. If you go to https://thingspeak.com/channels/66794 you should see the reported value.
At the gateway side, the cloud script that handles the ThingSpeak cloud is CloudThingSpeak.py. As ThingSpeak is a simple and very popular IoT cloud, we enhanced CloudThingSpeak.py to be able to assign a specific channel write key and a specific chart (field index) depending on the sensor source address. It is also possible to assign a specific field offset depending on the nomenclature. For more detail, read the examples provided in the CloudThingSpeak.py script.
The program has been tested on Arduino Uno, Mega2560, Nano, Pro Mini, Mini, Due, Zero. We also tested on the TeensyLC/3.1/3.2, the Ideetron Nexus and the Feather32u4/M0. Starting from November 3rd, 2017, the SPI_SS pin (CS pin) is always pin number 10 on all Arduino and Teensy boards.
Notice for low-cost/clone Arduino boards. If you get a low-cost Arduino board, such as those sold by most of Chinese manufacturer, the USB connectivity is probably based on the CH340 or CH341. To make your low-cost Arduino visible to your Arduino IDE, you need the specific driver. Look at http://sparks.gogo.co.nz/ch340.html or http://www.microcontrols.org/arduino-uno-clone-ch340-ch341-chipset-usb-drivers/. For MacOS, you can look at http://www.mblock.cc/posts/run-makeblock-ch340-ch341-on-mac-os-sierra which works for MacOS up to Sierra. For MacOS user that have the previous version of CH34x drivers and encountering kernel panic with Sierra, don't forget to delete previous driver installation: sudo rm -rf /System/Library/Extensions/usb.kext.
With the Arduino IDE, open the Arduino_LoRa_InteractiveDevice sketch (or the Arduino_LoRa_SX12XX_InteractiveDevice if you move to the SX12XX library which is advised because Arduino_LoRa_InteractiveDevice will not be maintained anymore). Then compile it and upload to an Arduino board. You might need an Arduino platform with more memory if you also connect a small OLED screen. By default, the interactive end-device has address 6 and runs in LoRa mode 1, SF12BW125.
Enter \!SGSH52UGPVAUYG3S#1#21.6 in the input window and press RETURN
The command will be sent to the gateway and you should see the gateway pushing the data to the ThingSpeak test channel. If you go to https://thingspeak.com/channels/66794 you should see the reported value.
> sudo ./lora_gateway | python ./post_processing_gw.py | python ./log_gw
The gateway can also be based on an Arduino board, as described in the web page. With the Arduino IDE, open the Arduino_LoRa_Gateway sketch, compile the code and upload to an Arduino board. Then follow instructions on how to use the Arduino board as a gateway. It is better to use a more powerful (and with more RAM memory such as the MEGA) Arduino platform for building the gateway.
When your radio module can run in the 433MHz band (for instance when the radio is based on SX1276 or SX1278 chip, such as the inAir4 from Modtronics) then you can test running at 433MHz as follows:
- select line
#define BAND433inArduino_LoRa_temporArduino_LoRa_Simple_temp - compile the
lora_gateway.cppwith#define BAND433 - or simply run your gateway with
lora_gateway --mode 1 --freq 433.3to be on the same setting thanArduino_LoRa_tempandArduino_LoRa_Simple_temp - there are 4 channels in the 433MHz band: 433.3MHz as
CH_00_433, 433.6MHz asCH_01_433, 433.9MHz asCH_02_433and 434.3MHz asCH_03_433.CH_00_433=433.3MHz is the default channel in the 433MHz band.
For 900MHz band the procedure is similar:
- select line
#define BAND900inArduino_LoRa_temporArduino_LoRa_Simple_temp - compile the
lora_gateway.cppwith#define BAND900 - or simply run your gateway with
lora_gateway --mode 1 --freq 913.88to be on the same setting thanArduino_LoRa_tempandArduino_LoRa_Simple_temp - there are 13 channels in the 900MHz band: from
CH_00_900toCH_12_900.CH_05_900=913.88MHz is the default channel in the 900MHz band.
With sshfs:
-
look at http://mitchtech.net/dropbox-on-raspberry-pi-via-sshfs/. No need of
sudo gpasswd -a pi fuseon Jessie.sudo apt-get install sshfs
-
then allow option
user_allow_otherin/etc/fuse.conf
with Dropbox uploader:
- look at http://anderson69s.com/2014/02/18/raspberry-pi-dropbox/
- look at http://raspi.tv/2013/how-to-use-dropbox-with-raspberry-pi
- look at https://github.com/andreafabrizi/Dropbox-Uploader
- but not tested yet and not supported yet
Pre-defined LoRa modes from initial Libelium SX1272.h, except mode 11 to indicate LoRaWAN compatibility mode with sync word set to public LoRaWAN sync word (i.e. 0x34 for SX127X and 0x3444 for SX126X) instead of private sync word (i.e. 0x12 for SX127X and 0x1424 for SX126X) for all other mode. For SX128X in LoRa 2.4GHz band, BW 125, 250 and 500 are replaced respectively by BW 203, 406 and 812 while SF remains the same.
| mode | BW | SF |
|---|---|---|
| 1 | 125 | 12 |
| 2 | 250 | 12 |
| 3 | 125 | 10 |
| 4 | 500 | 12 |
| 5 | 250 | 10 |
| 6 | 500 | 11 |
| 7 | 250 | 9 |
| 8 | 500 | 9 |
| 9 | 500 | 8 |
| 10 | 500 | 7 |
| 11 | 125 | 12 |
Pre-defined channels in 868MHz, 915MHz and 433MHz band (most of them from initial Libelium SX1272.h, except those marked with *). Frequencies in bold are those used by default in each band.
| ch | F(MHz) | ch | F(MHz) | ch | F(MHz) |
|---|---|---|---|---|---|
| 04 | 863.2* | 00 | 903.08 | 00 | 433.3* |
| 05 | 863.5* | 01 | 905.24 | 01 | 433.6* |
| 06 | 863.8* | 02 | 907.40 | 02 | 433.9* |
| 07 | 864.1* | 03 | 909.56 | 03 | 434.3* |
| 08 | 864.4* | 04 | 911.72 | - | - |
| 09 | 864.7* | 05 | 913.88 | - | - |
| 10 | 865.2 | 06 | 916.04 | - | - |
| 11 | 865.5 | 07 | 918.20 | - | - |
| 12 | 865.8 | 08 | 920.36 | - | - |
| 13 | 866.1 | 09 | 922.52 | - | - |
| 14 | 866.4 | 10 | 924.68 | - | - |
| 15 | 867.7 | 11 | 926.84 | - | - |
| 16 | 867.0 | 12 | 915.00 | - | - |
| 17 | 868.0 | - | - | - | - |
| 18 | 868.1* | - | - | - | - |
| - | - | - | - | - | - |
Verify if the low-level gateway program detects your radio module and if the radio module is working by simply run the low-level gateway program with:
> sudo ./lora_gateway
You should see the following output, here for an SX127X based gateway
^$**********Power ON
^$Frequency 865200000
^$LoRa addr 1
^$Use PA_BOOST amplifier line
^$Set LoRa txpower dBm to 14
^$Preamble Length: 8
^$Sync word: 0x12
^$SX1276,865199936hz,SF12,BW125000,CR4:5,LDRO_On,SyncWord_0x12,IQNormal,Preamble_8
^$SX1276,SLEEP,Version_12,PacketMode_LoRa,Explicit,CRC_On,AGCauto_On,LNAgain_1,LNAboostHF_On,LNAboostLF_On
^$SX127X configured as LR-BS. Waiting RF input for transparent RF-serial bridge
-
There is currently no control on the transmit time for both gateway and end-device. When using the library to create devices, you have to ensure that the transmit time of your device is not exceeding the legal maximum transmit time defined in the regulation of your country (for instance ETSI define 1% duty-cycle, i.e. 36s/hour).
-
Although 900MHz band is supported (mostly for the US ISM band), the library does not implement the frequency hopping mechanism nor the limited dwell time (e.g. 400ms per transmission).
Specific developments can be made from the general, public version on github. The framework has been used for instance in Nestlé's WaterSense project and HygieItalia's WISMART project. If you are interested by such customization (advanced and reliable downlink, dynamic and reconfigurable measure interval, PCBs with integrated antennas,...) you can contact me.
June 19th, 2020. The low-cost, low-power and long-distance cattle collar developed in the EU H2020 WAZIUP project has been identified by the European Commission's Innovation Radar. The WAZIUP project which has been coordinated by Abdur Rahim from FBK/CREATE-NET focused on deploying low-cost IoT technologies across Africa. From an original idea of Prof. Congduc Pham from University of Pau, the low-cost, low-power and long-distance cattle collar has further been jointly developed and tested with a team of researchers (Ousmane Dieng, Mamour Diop and Babacar Diop) from University of Gaston Berger (Saint-Louis, Senegal) led by Prof Ousmane Thiaré. Large-scale testing facility has been provided by the CIMEL experimental farm in Saint-Louis, Senegal. The Arduino example of the GPS Cattle Collar is Arduino_LoRa_Simple_GPS. The dedicated tutorial describing the low-cost, low-power and long-distance cattle collar is [Low-cost-LoRa-Collar.pdf]((https://github.com/CongducPham/tutorials/blob/master/Low-cost-LoRa-Collar.pdf)
Related publications:
[1] O. Dieng, B. Diop, O. Thiaré, C. Pham, "A Study on IoT Solutions for Preventing Cattle Rustling in African Context". Proceeding of the second International Conference on Internet of Things Data, and Cloud Computing (ICC'17), Cambridge , United Kingdom, 22-23 March 2017.
[2] O. Dieng, C. Pham and O. Thiaré, "Outdoor Localization and Distance Estimation Based on Dynamic RSSI Measurements in LoRa Networks: Application to Cattle Rustling Prevention", Proceedings of the 15th IEEE WiMob'2019, October 21-23, 2019, Barcelona, Spain.
[3] Dedicated tutorial describing the low-cost, low-power and long-distance cattle collar.
Enjoy! C. Pham