Weaveworks is the company that develops Weave - the most productive way for developers to connect, observe and control Docker containers. To learn about our products, including getting started tutorials, visit our website and documentation or continue to read about some of the more technical aspects of Weave in this readme.
Weave creates a virtual network that connects Docker containers deployed across multiple hosts and enables their automatic discovery.
Applications use the network just as if the containers were all plugged into the same network switch, with no need to configure port mappings, links, etc. Services provided by application containers on the weave network can be made accessible to the outside world, regardless of where those containers are running. Similarly, existing internal systems can be exposed to application containers irrespective of their location.
Weave can traverse firewalls and operate in partially connected networks. Traffic can be encrypted, allowing hosts to be connected across an untrusted network.
With weave you can easily construct applications consisting of multiple containers, running anywhere.
Weave works alongside Docker's existing (single host) networking capabilities, so these can continue to be used by containers.
Ensure you are running Linux (kernel 3.8 or later) and have Docker (version 1.6.0 or later) installed. Then install weave with
sudo curl -L git.io/weave -o /usr/local/bin/weave
sudo chmod a+x /usr/local/bin/weave
For usage on OSX (with Docker Machine) you first need to make sure that a VM is running and configured. Then you can launch weave directly from the OSX host.
For installing weave on other platforms, follow the integration guides.
Weave respects the environment variable DOCKER_HOST, so you can run
it locally to control a weave network on a remote host.
Say you have docker running on two hosts, accessible to each other as
$HOST1 and $HOST2, and want to deploy an application consisting of
two containers, one on each host.
On $HOST1 we run:
host1$ weave launch
host1$ eval $(weave env)
host1$ docker run --name a1 -ti ubuntu
NB: If the first command results in an error like
http:///var/run/docker.sock/v1.19/containers/create: dial unix /var/run/docker.sock: permission denied. Are you trying to connect to a TLS-enabled daemon without TLS?then you likely need to be 'root' in order to connect to the Docker daemon. If so, run the above and all subsequent commands in a single root shell (e.g. one created withsudo -s). Do not prefix individual commands withsudo, since some commands modify environment entries and hence they all need to be executed from the same shell.
The first line runs weave. The second line configures our environment so that containers launched via the docker command line are automatically attached to the weave network. Finally, we run our application container.
That's it! If our application consists of more than one container on
this host we simply launch them with docker run as appropriate.
Next we repeat similar steps on $HOST2...
host2$ weave launch $HOST1
host2$ eval $(weave env)
host2$ docker run --name a2 -ti ubuntu
The only difference, apart from the name of the application container,
is that we tell our weave that it should peer with the weave on
$HOST1 (specified as the IP address or hostname, and optional
:port, by which $HOST2 can reach it). NB: if there is a firewall
between $HOST1 and $HOST2, you must permit traffic to the weave
control port (TCP 6783) and data ports (UDP 6783/6784).
Note that we could instead have told the weave on $HOST1 to connect to
$HOST2, or told both about each other. Order does not matter here;
weave automatically (re)connects to peers when they become
available. Also, we can tell weave to connect to multiple peers by
supplying multiple addresses, separated by spaces. And we can
add peers dynamically.
Weave must be started once per host. The relevant container images are
pulled down on demand, but if you wish you can preload them by running
weave setup - this is particularly useful for automated deployments,
and ensures that there are no delays during later operations.
Now that we've got everything set up, let's see whether our containers can talk to each other...
In the container started on $HOST1...
root@a1:/# ping -c 1 -q a2
PING a2.weave.local (10.40.0.2) 56(84) bytes of data.
--- a2.weave.local ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.341/0.341/0.341/0.000 ms
Similarly, in the container started on $HOST2...
root@a2:/# ping -c 1 -q a1
PING a1.weave.local (10.32.0.2) 56(84) bytes of data.
--- a1.weave.local ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.366/0.366/0.366/0.000 ms
So there we have it, two containers on separate hosts happily talking to each other.
Found a bug, want to suggest a feature, or have a question? Please
file an issue, or post
to the
Weave Users Google Group,
which you can email at [email protected]. Or you can contact
Weaveworks directly at [email protected]. When reporting a bug, please
include which version of weave you are running, as shown by weave version.
Follow on Twitter: @weaveworks.
Read the Weave blog: Weaveblog.
IRC: #weavenetwork