I'm going to guess you're here because you want to set up basic UPS monitoring on a Raspberry Pi or similar Linux system.
You are in the right place, Internet Stranger. There's a strong possibility you've been searching the Internet for a solution, so let's start with telling you what you can expect to find if you keep reading:
- What? A basic script that installs Network UPS Tools (NUT) and some other packages.
- How? By downloading our script and running it on a Raspberry Pi or similar Linux system.
- Why? So you can have HTTP and SNMP v2c monitoring within minutes of running the script.
Of course, there's more you may want to do with your UPS software like adding shutdown configurations, monitoring multiple UPSes, or hardening the setup with encrypted protocols and secure configurations. To help you get started with that, we'll also review how the script works and provide some tips on how you can extend it or manually configure NUT to meet specific needs.
And, this isn't just a one-off post. We plan to update the process and script over time based on user feedback. You can even directly contribute! Just make a pull request with your suggested improvements.
Here's an Asciicast of what the script method looks like:
The Network UPS Tools (NUT) project does a lot of good work in our industry. A lot of the UPS integrations you see in various systems (e.g., NAS devices and console servers) are made possible by NUT. Simply put, there is a lot of cool stuff you can do with NUT.
But, we often see these problems:
- People don't know all the cool stuff NUT can do
- NUT can be complex to configure if you don't know where to start
So, we wanted to let you know about NUT and make it easy to get started. We also wanted to get some conversations going around what you want to be able to do with your Linux systems and UPSes, and make this project collaborative between us and the community. So, if you have ideas, feature requests, comments, notice bugs, or do something cool with Network UPS Tools, let us know.
This process should work with a wide variety of UPS systems with a USB port. That said, our testing has been with select Tripp Lite and Eaton branded UPSes. Here's a running list of recommended UPSes:
- A supported UPS.
- A Linux computer running Raspberry Pi OS, Ubuntu, or a similar operating system that uses
apt
- root/sudo privleges
- A USB connection between the UPS and the Linux computer. You can confirm the UPS is connected using the
lsusb
command. In the example below, we see aTRIPPLITE UPS
- Ports 161 (UDP), 80 (TCP), and 3493 (TCP) open
- None of these packages installed:
- nut
- nut-cgi
- snmp
- snmpd
- libsnmp-dev
- snmp-mibs-downloader
- net-snmp
- Access your computer's terminal (e.g., via SSH)
- Download the script
wget https://raw.githubusercontent.com/dzomaya/NUTandRpi/main/scripts/nutinstall.sh
sudo chmod +x nutinstall.sh
- Run the script
sudo ./nutinstall.sh
- At the
If you haven't updated your package lists with a command like apt-get update or apt update within the last day or so, you should do that now. Want us to run apt update for you? Answer y for yes or anything else for no.
prompt, answery
if you want to runapt update -y
now or answern
to skip runningapt update -y
here. If you ranapt update
orapt-get update
before running the script,n
is the right answer. - At the
Do you want to assume the risk and continue? Enter 'y' for yes or 'n' for no.
prompt, entery
to assume the risk and continue. - At the 'Tell me what SNMP v2c community string I should use for your configuration:' prompt, input a 1-32 character alphanumeric SNMP v2c community string. This is the community string that the script will use to configure your SNMP settings.
- Now the script will run and configure Network UPS Tools, the nut-cgi package (including Apache), and your SNMP settings. This can take a couple of minutes. At the end of the script, you should see a message similar to:
You should now be able to see cool UPS stats at http://localhost/cgi-bin/nut/upsstats.cgi.
'snmpwalk -v2c -c <the community from earlier> localhost .1.3.6.1.4.1.8072.1.3.2.4.1.2' should give you some SNMP data too.
This was fun. Thanks. Have a great day Internet Freind. Goodbye
That's it! You're off to the races with your UPS monitoring.
Now you can do cool stuff like:
- Browse to http://yourRasberryPiIPaddress/cgi-bin/nut/upsstats.cgi and an overview of UPS status
- Browse to http://yourRasberryPiIPaddress/cgi-bin/nut/upsstats.cgi?host=nutdev1@localhost and see a dashboard of UPS UPS statistics
- Browse to http://yourRasberryPiIPaddress/cgi-bin/nut/upsstats.cgi?host=nutdev1@localhost&treemode and see a list of all supported UPS variables
- Use SNMP tools to capture UPS data, like this:
snmpwalk -v2c -c yourSNMPv2cCommunity yourRasberryPiIPaddress .1.3.6.1.4.1.8072.1.3.2.4.1.2
Output should look similar to
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsmfr".1 = STRING: TRIPPLITE
NET-SNMP-EXTEND-MIB::nsExtendOutLine."inputHZ".1 = STRING: 59.9
NET-SNMP-EXTEND-MIB::nsExtendOutLine."outputHZ".1 = STRING: 59.9
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsmodel".1 = STRING: TRIPPLITE UPS
NET-SNMP-EXTEND-MIB::nsExtendOutLine."battvolts".1 = STRING: 54.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."inputvolt".1 = STRING: 126.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsserial".1 = STRING: 3104JLCPS795200451
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsstatus".1 = STRING: OL
NET-SNMP-EXTEND-MIB::nsExtendOutLine."battcharge".1 = STRING: 100
NET-SNMP-EXTEND-MIB::nsExtendOutLine."outputload".1 = STRING: 0.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."outputvolt".1 = STRING: 120.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."battruntimeest".1 = STRING: 65535
Now that you've exposed the data via SNMP, you can use a wide-range of monitoring utilites like NagiOS, LibreNMS, and Observium to do all sorts of cool things.
You can read up on the OIDs we used in the OID explainer.
Our script won't work for everyone and you learn more doing it manually anyway, so let's walk through how you can manually install and configure NUT.
- A supported UPS.
- A Linux computer running Raspberry Pi OS, Ubuntu, or a similar operating system
- Just about any *nix system should work, our commands just assume Ubuntu-like stuff such as the
apt
command
- Just about any *nix system should work, our commands just assume Ubuntu-like stuff such as the
- root/sudo privleges to run commands
- A USB connection between the UPS and the Linux computer. You can confirm the UPS is connected using the
lsusb
command. In the example below, we see aTRIPPLITE UPS
- Ports 161 (UDP), 80 (TCP), and 3493 (TCP) open
- None of these packages installed:
- nut
- nut-cgi
- snmp
- snmpd
- libsnmp-dev
- snmp-mibs-downloader
- net-snmp
If you haven't updated your system in a while, it's a good idea to access your computer's terminal (e.g., via SSH) and run:
sudo apt update
To make sure you get the latest available packages in the next steps.
- Access your computer's terminal (e.g., via SSH)
- Use
apt
to install thenut
andnut-cgi
packages
sudo apt install nut nut-cgi
- Run this command:
nut-scanner -UNq
The output should look similar to:
SNMP library not found. SNMP search disabled.
Neon library not found. XML search disabled.
IPMI library not found. IPMI search disabled.
[nutdev1]
driver = "usbhid-ups"
port = "auto"
vendorid = "09AE"
productid = "4004"
bus = "003"
You'll need everything under (and including) [nutdev1]
for the next step.
- Use a text editor (e.g.,
nano
orvi
) to edit /etc/nut/ups.conf and append the output from step 1. Using our example output, the uncommented section of the ups.conf file should look like this:
maxretry = 3
[nutdev1]
driver = "usbhid-ups"
port = "auto"
vendorid = "09AE"
productid = "4004"
bus = "003"
- Use a text editor (e.g.
nano
orvi
) to edit /etc/nut/nut.conf to read
MODE=netserver
4. Make sure your UPS is now communicating by running the upsc nutdev1
command. Output should look similar to:
Init SSL without certificate database
battery.charge: 100
battery.charge.low: 20
battery.charge.warning: 20
battery.runtime: 65535
battery.temperature: 28.9
battery.type: PbAc
battery.voltage: 54.0
battery.voltage.nominal: 48.0
device.mfr: TRIPPLITE
device.model: TRIPPLITE UPS
device.serial: 3104JLCPS795200451
device.type: ups
driver.name: usbhid-ups
driver.parameter.bus: 003
driver.parameter.pollfreq: 30
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.parameter.product: TRIPPLITE UPS
driver.parameter.productid: 4004
driver.parameter.serial: 3104JLCPS795200451
driver.parameter.synchronous: no
driver.parameter.vendor: TRIPPLITE
driver.parameter.vendorid: 09AE
driver.version: 2.7.4
driver.version.data: TrippLite HID 0.82
driver.version.internal: 0.41
input.frequency: 60.0
input.transfer.high: 150.0
input.transfer.high.max: 150
input.transfer.high.min: 145
input.transfer.low: 55.0
input.transfer.low.max: 60
input.transfer.low.min: 55
input.voltage: 126.0
input.voltage.nominal: 120
output.current: 0.0
output.frequency: 60.0
output.frequency.nominal: 60
output.voltage: 120.0
output.voltage.nominal: 120
ups.beeper.status: enabled
ups.delay.shutdown: 20
ups.delay.start: 30
ups.firmware: 64
ups.load: 0
ups.mfr: TRIPPLITE
ups.model: TRIPPLITE UPS
ups.power: 0.0
ups.power.nominal: 2200
ups.productid: 4004
ups.serial: 3104JLCPS795200451
ups.status: OL
ups.test.result: Done and passed
ups.timer.reboot: 0
ups.timer.shutdown: -1
ups.timer.start: 0
ups.vendorid: 09ae
ups.watchdog.status: 0
- Add your UPS to the NUT hosts.conf file by using a text editor (e.g.
nano
orvi
) to edit /etc/nut/hosts.conf and add this line to the end of the file:
MONITOR nutdev1@localhost \"Pepper and Egg UPS\"
- Apache was installed when we intsalled the
nut-cgi
package. Enable the cgi module with this command:
a2enmod cgi
You should see output similar to:
Your MPM seems to be threaded. Selecting cgid instead of cgi.
Enabling module cgid.
To activate the new configuration, you need to run:
systemctl restart apache2
- Restart Apache with this command:
systemctl restart apache2
- Use
apt
to install thesnmp
,snmpd
,libsnmp-dev
, andsnmp-mibs-downloader
packages
sudo apt install snmp snmpd libsnmp-dev snmp-mibs-downloader
- Use a text editor (e.g.,
nano
orvi
) to create an /etc/snmp/snmpd.conf file and add your SNMP v2c community string to the begining. To create a read-onlytripplite
, add this entry (edit your community string to be something only you know):
rocommunity tripplite
Don't save your changes just yet, we have some more edits to make.
- Next, we're going to add
upsc
commands to the /etc/snmp/snmpd.conf. For our example, we'll add these 12 lines:
extend-sh upsmodel "/bin/upsc nutdev1 ups.model"
extend-sh upsmodel "/bin/upsc nutdev1 ups.model"
extend-sh upsserial "/bin/upsc nutdev1 ups.serial"
extend-sh upsstatus "/bin/upsc nutdev1 ups.status"
extend-sh battcharge "/bin/upsc nutdev1 battery.charge"
extend-sh battruntimeest "/bin/upsc nutdev1 battery.runtime"
extend-sh battvolts "/bin/upsc nutdev1 battery.voltage"
extend-sh inputvolt "/bin/upsc nutdev1 input.voltage"
extend-sh inputHZ "/bin/upsc nutdev1 input.frequency"
extend-sh outputvolt "/bin/upsc nutdev1 output.voltage"
extend-sh outputHZ "/bin/upsc nutdev1 output.frequency"
extend-sh outputHZ "/bin/upsc nutdev1 output.frequency"
Now, save your changes. The file should look like this when you're done:
- Enable the snmpd service
sudo systemctl enable snmpd
- Restart the snmpd service
sudo systemctl restart snmpd
That's it! You're off to the races with your UPS monitoring.
Now you can do cool stuff like:
- Browse to http://yourRasberryPiIPaddress/cgi-bin/nut/upsstats.cgi and an overview of UPS status
- Browse to http://yourRasberryPiIPaddress/cgi-bin/nut/upsstats.cgi?host=nutdev1@localhost and see a dashboard of UPS UPS statistics
- Browse to http://yourRasberryPiIPaddress/cgi-bin/nut/upsstats.cgi?host=nutdev1@localhost&treemode and see a list of all supported UPS variables
- Use SNMP tools to capture UPS data, like this:
snmpwalk -v2c -c yourSNMPv2cCommunity yourRasberryPiIPaddress .1.3.6.1.4.1.8072.1.3.2.4.1.2
Output should look similar to
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsmfr".1 = STRING: TRIPPLITE
NET-SNMP-EXTEND-MIB::nsExtendOutLine."inputHZ".1 = STRING: 59.9
NET-SNMP-EXTEND-MIB::nsExtendOutLine."outputHZ".1 = STRING: 59.9
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsmodel".1 = STRING: TRIPPLITE UPS
NET-SNMP-EXTEND-MIB::nsExtendOutLine."battvolts".1 = STRING: 54.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."inputvolt".1 = STRING: 126.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsserial".1 = STRING: 3104JLCPS795200451
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsstatus".1 = STRING: OL
NET-SNMP-EXTEND-MIB::nsExtendOutLine."battcharge".1 = STRING: 100
NET-SNMP-EXTEND-MIB::nsExtendOutLine."outputload".1 = STRING: 0.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."outputvolt".1 = STRING: 120.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."battruntimeest".1 = STRING: 65535
Now that you've exposed the data via SNMP, you can use a wide-range of monitoring utilites like NagiOS, LibreNMS, and Observium to do all sorts of cool things.
You can read up on the OIDs we used in the OID explainer.
What we've done here will give you a good starting point for UPS monitoring. That said, we know there are plenty of other things you might want to do. We might even up date this project to do some of them in the future, but for now here are some tips to point you in the right direction.
If you just want to explore what you can do in general, Roger Price has done a great job with NUT documentation: https://rogerprice.org/NUT/
Often, you'll want to gracefully shutdown operating systems and shut down UPS output based on certain UPS events. upsmon
and section 6.3 of the NUT User's Manual is a good place to start. There is a full PDF version of the manual here.
Again, the NUT User's Guide and Techno Tim video are good references. For a straightforward use case, consider starting with adding additional USB-connected UPSes in your /etc/nut/ups.conf
file.
Grafana is a great open source project for data visualization and graphing. Once you have NUT and Net-SNMP configured it's possible to take those values and graph them in Grafana. For example, I used Grafana, InfluxDB, and Telegraf to put this together using data from one of our NUT/Net-SNMP installs.
Additionally, Grafana is extensible enough that you could even take SNMP out of the mix altogether and use upsc
or similar to capture the data.
SNMP v3 is a bit more complex than SNMP v2c, but it also uses encryption and is significantly more secure. For a deep understanding of Net-SNMP configuration, you should check out their docs.
If you're just testing, a quick way to get started creating SNMP v3 users is to use the net-snmp-config --create-snmpv3-user
command.
For example, to create a PiNutAdmin
SNMP v3 user with read-only permissions that uses AES and SHA with an auth and privacy passwords both set to pepperandegg
, we can do this:
- Stop the snmpd service
sudo systemctl stop snmpd
- Run the command to create the user
sudo net-snmp-config --create-snmpv3-user -ro -x AES -a SHA -A "pepperandegg" -X "pepperandegg" PiNutAdmin
- Start the snmpd service
sudo systemctl start snmpd
- Run an
snmpwalk
to see if your user can read UPS datasnmpwalk -v 3 -u PiNutAdmin -l AuthPriv -x AES -a SHA -X pepperandegg -A pepperandegg localhost .1.3.6.1.4.1.8072.1.3.2.4.1.2
You should see output similar to:
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsmfr".1 = STRING: TRIPPLITE
NET-SNMP-EXTEND-MIB::nsExtendOutLine."inputHZ".1 = STRING: 59.9
NET-SNMP-EXTEND-MIB::nsExtendOutLine."outputHZ".1 = STRING: 59.9
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsmodel".1 = STRING: TRIPPLITE UPS
NET-SNMP-EXTEND-MIB::nsExtendOutLine."battvolts".1 = STRING: 54.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."inputvolt".1 = STRING: 126.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsserial".1 = STRING: 3104JLCPS795200451
NET-SNMP-EXTEND-MIB::nsExtendOutLine."upsstatus".1 = STRING: OL
NET-SNMP-EXTEND-MIB::nsExtendOutLine."battcharge".1 = STRING: 100
NET-SNMP-EXTEND-MIB::nsExtendOutLine."outputload".1 = STRING: 0.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."outputvolt".1 = STRING: 120.0
NET-SNMP-EXTEND-MIB::nsExtendOutLine."battruntimeest".1 = STRING: 65535
If you want to undo what the script did and uninstall the packages it installs, follow these steps.
rm -rf
is mentioned and used in some of the steps below. rm -rf
recursively deletes files. Be careful!
- Remove the packages the script installs with this command:
sudo apt-get remove nut nut-cgi snmp snmpd libsnmp-dev snmp-mibs-downloader
- Remove the unneeded packages left behind after you removed the packages:
sudo apt-get autoremove
- Remove the
snmpd.conf
file the script modifies
sudo rm /etc/snmp/snmpd.conf
Note: If you want to remove the MIB files in /etc/snmp/
and the /etc/snmp
directory completely, use sudo rm -rf /etc/snmp/
.
- Remove the
/etc/nut
directory and it's contents:
sudo rm -rf /etc/nut
We want to hear from you.
- If you have a suggested improvement for the scripts or process, make a pull request.
- If you notice a bug or have a feature request, report an issue.
- If you're from an organization that needs a solution for a specific Linux/UPS application, shoot me a message.
Good bye and good luck, Internet Stranger.