Update Zone3D Printer profile

resources/machine_profiles/Zone3d Printer.ini

@@ -1,18 +1,120 @@
-[machine]
+[profile]
 machine_name = Zone3D Printer
 machine_type = Zone3D Printer
-machine_width = 240
-machine_depth = 220
-machine_height = 210
-machine_center_is_zero = False
-has_heated_bed = True
 gcode_flavor = RepRap (Marlin/Sprinter)
-extruder_amount = 1
-
-[profile]
-filament_diameter = 1.75
+layer_height = 0.2
+wall_thickness = 1.0
+retraction_enable = True
+solid_layer_thickness = 0.2
+fill_density = 15
 nozzle_size = 0.4
-layer_height = 0.14
-print_speed = 50
+print_speed = 40
 print_temperature = 260
+print_temperature2 = 0
+print_temperature3 = 0
+print_temperature4 = 0
+print_temperature5 = 0
+print_bed_temperature = 100
+support = Touching buildplate
+platform_adhesion = None
+support_dual_extrusion = Both
+wipe_tower = False
+wipe_tower_volume = 15
+ooze_shield = False
+filament_diameter = 1.75
+filament_diameter2 = 0
+filament_diameter3 = 0
+filament_diameter4 = 0
+filament_diameter5 = 0
+filament_flow = 100.0
+retraction_speed = 20.0
+retraction_amount = 0.6
+retraction_dual_amount = 16.5
+retraction_min_travel = 1.5
+retraction_combing = True
+retraction_minimal_extrusion = 0.02
+retraction_hop = 0.0
+bottom_thickness = 0.3
+layer0_width_factor = 100
+object_sink = 0.0
+overlap_dual = 0.15
 travel_speed = 150
+bottom_layer_speed = 20
+infill_speed = 0.0
+solidarea_speed = 0.0
+inset0_speed = 20
+insetx_speed = 70
+cool_min_layer_time = 5
+fan_enabled = True
+skirt_line_count = 1
+skirt_gap = 3.0
+skirt_minimal_length = 150.0
+fan_full_height = 0.5
+fan_speed = 100
+fan_speed_max = 100
+cool_min_feedrate = 10
+cool_head_lift = False
+solid_top = True
+solid_bottom = True
+fill_overlap = 15
+support_type = Lines
+support_angle = 45
+support_fill_rate = 15
+support_xy_distance = 0.7
+support_z_distance = 0.17
+spiralize = False
+simple_mode = False
+brim_line_count = 20
+raft_margin = 5.0
+raft_line_spacing = 3.0
+raft_base_thickness = 0.3
+raft_base_linewidth = 1.0
+raft_interface_thickness = 0.27
+raft_interface_linewidth = 0.4
+raft_airgap_all = 0.0
+raft_airgap = 0.22
+raft_surface_layers = 2
+raft_surface_thickness = 0.27
+raft_surface_linewidth = 0.4
+fix_horrible_union_all_type_a = True
+fix_horrible_union_all_type_b = False
+fix_horrible_use_open_bits = False
+fix_horrible_extensive_stitching = False
+plugin_config = (lp1
+	.
+object_center_x = -1
+object_center_y = -1
+
+[alterations]
+start.gcode = ;Sliced at: {day} {date} {time}
+	;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+	;Print time: {print_time}
+	;Filament used: {filament_amount}m {filament_weight}g
+	;Filament cost: {filament_cost}
+	;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
+	;M109 S{print_temperature} ;Uncomment to add your own temperature line
+	M107
+	G21        ;metric values
+	G90        ;absolute positioning
+	M82        ;set extruder to absolute mode
+	M107       ;start with the fan off
+	G28 X0 Y0  ;move X/Y to min endstops
+	G28 Z0     ;move Z to min endstops
+	G1 Z15.0 F{travel_speed} ;move the platform down 15mm
+	G92 E0                  ;zero the extruded length
+	G1 F200 E10              ;extrude 10mm of feed stock
+	G92 E0                  ;zero the extruded length again
+	G1 F{travel_speed}
+	;Put printing message on LCD screen
+	M117 Printing...
+end.gcode = ;End GCode
+	M104 S0                     ;extruder heater off
+	M140 S0                     ;heated bed heater off (if you have it)
+	G91                                    ;relative positioning
+	G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+	G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+	G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
+	M84                         ;steppers off
+	G90                         ;absolute positioning
+	;{profile_string}
+