Skip to content

ZuluSpl0it/Toyota_Spd_SAS_Tester

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

16 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Toyota_Spd_SAS_Tester

This project is for a Toyota Steering Angle Sensor (SAS) tester. The tester also includes the capability to calculate speed based on a VSS signal.

I created this tester in order to confirm the precision of several SAS units I had acquired in the hopes of adding openpilot to my old car . I was confused as to why some people stated that the resolution of the TSS1 SAS was only 1.5 degrees while others stated that the sensors were good to 0.1 degrees.

The hardware components are:

  • STM32F1 Bluepill (using STM32duino core)
  • MCP2515 CAN Bus Module (SPI)
  • 0.96 Inch OLED 128x64 Module (I2C)
  • 2 SPST switches
  • 82K and 2.2K resistors

The switches select between mode of operation (Angle or Speed) and SAS precision (High and Low).

Low and High precision refer to either 1.5 degree or 0.1 degree resolution from the SAS.

Bluepill pinout

bluepin pinout

Here are the results of my testing:

Part# Precision
89245-02080 High (0.1 deg resolution)
89245-0R020 Low (1.5 deg resolution)
89245-07020 Low (1.5 deg resolution)

CAN message detail (for high precision sensor)

The High precision SAS sends a CAN message in the following format:

 BO_ 37 STEER_ANGLE_SENSOR: 8 XXX  
    SG_ STEER_ANGLE : 3|12@0- (1.5,0) [-500|500] "deg" XXX  
    SG_ STEER_FRACTION : 39|4@0- (0.1,0) [-0.7|0.7] "deg" XXX  
    SG_ STEER_RATE : 35|12@0- (1,0) [-2000|2000] "deg/s" XXX  

Visually, it looks like this:

    Name:       STEER_ANGLE_SENSOR
    Id:         HEX = 0x25        Decimal = 37
    Length:     8 bytes
    Cycle time: - ms
    Senders:    XXX
    Layout:
                          Bit

             7   6   5   4   3   2   1   0
           +---+---+---+---+---+---+---+---+
         0 |   |   |   |   |<--------------|
           +---+---+---+---+---+---+---+---+
         1 |------------------------------x|
           +---+---+---+---+---+---+---+---+
                                         └-- STEER_ANGLE   [Min = -500   Max = 500]   (Units = deg)
           +---+---+---+---+---+---+---+---+
         2 |   |   |   |   |   |   |   |   |
           +---+---+---+---+---+---+---+---+
     B   3 |   |   |   |   |   |   |   |   |
     y     +---+---+---+---+---+---+---+---+
     t   4 |<-------------x|<--------------|
     e     +---+---+---+---+---+---+---+---+
                         └-- STEER_FRACTION   [Min = -0.7   Max = 0.7]   (Units = deg)
           +---+---+---+---+---+---+---+---+
         5 |------------------------------x|
           +---+---+---+---+---+---+---+---+
                                         └-- STEER_RATE   [Min = -2000   Max = 2000]   (Units = deg/s)
           +---+---+---+---+---+---+---+---+
         6 |   |   |   |   |   |   |   |   |
           +---+---+---+---+---+---+---+---+
         7 |   |   |   |   |   |   |   |   |
           +---+---+---+---+---+---+---+---+

    Signal tree:

    -- {root}
       └-- STEER_ANGLE
       └-- STEER_FRACTION              Note: 1/15th of the signal STEER_ANGLE, which
                                       is 1.5 deg; note that 0x8 is never set
       └-- STEER_RATE                  Note: factor is tbd

Then following table is a parital listing of the final calculated Steering Angle:

Steer Angle Calculation Table

The 89245-02080 sensor passes both high and low tests:

High Test
Low Test

However, the other sensors fail the high precision test, while passing the low precision test:

High Test
Low Test

The reason for this is because the low precision sensors do not have the Steer Fraction at all in their CAN messages, Instead that byte is used for other data:

Older Sensor
from: Adventures in Automotive Networks and Control Units (page 93) By Dr. Charlie Miller & Chris Valasek

About

No description, website, or topics provided.

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published