ISolar SPR 1KW support

[allbeq]

Hi Team,

Im trying to connect with your project to my "ups".
I have checked main and 2424mse1 branches and faced with problem.

Succesfully build hardware side, my log looks as following:

[21:25:17][D][pipsolar:838]: Sending polling command : QMOD with length 4
[21:25:17][D][pipsolar:772]: checking crc on incoming message
[21:25:17][D][pipsolar:775]: CRC OK
[21:25:17][D][pipsolar:471]: Decode QMOD
[21:25:17][D][text_sensor:067]: 'isolarups device_mode': Sending state 'M'
[21:25:18][D][pipsolar:838]: Sending polling command : QFLAG with length 5
[21:25:18][D][pipsolar:772]: checking crc on incoming message
[21:25:18][D][pipsolar:775]: CRC OK
[21:25:18][D][pipsolar:479]: Decode QFLAG
[21:25:19][D][pipsolar:838]: Sending polling command : QPIRI with length 5
[21:25:19][D][pipsolar:772]: checking crc on incoming message
[21:25:19][D][pipsolar:775]: CRC OK
[21:25:19][D][pipsolar:429]: Decode QPIRI
[21:25:20][D][pipsolar:838]: Sending polling command : QPIGS with length 5
[21:25:20][D][pipsolar:772]: checking crc on incoming message
[21:25:20][D][pipsolar:775]: CRC OK
[21:25:20][D][pipsolar:448]: Decode QPIGS
[21:25:20][D][sensor:127]: 'isolarups grid_voltage': Sending state 0.00000 V with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups grid_frequency': Sending state 0.00000 Hz with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups ac_output_voltage': Sending state 0.00000 V with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups ac_output_frequency': Sending state 0.00000 Hz with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups ac_output_apparent_power': Sending state 0.00000 VA with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups ac_output_active_power': Sending state 0.00000 W with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups output_load_percent': Sending state 0.00000 % with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups bus_voltage': Sending state 0.00000 V with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups battery_voltage': Sending state 0.00000 V with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups battery_charging_current': Sending state 0.00000 A with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups battery_capacity_percent': Sending state 0.00000 % with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups inverter_heat_sink_temperature': Sending state 0.00000 °C with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups pv_input_current_for_battery': Sending state 0.00000 A with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups pv_input_voltage': Sending state 0.00000 V with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups battery_voltage_scc': Sending state 0.00000 V with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups battery_discharge_current': Sending state 0.00000 A with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups battery_voltage_offset_for_fans_on': Sending state 0.00000 V with 1 decimals of accuracy
[21:25:20][D][sensor:127]: 'isolarups pv_charging_power': Sending state 0.00000 W with 1 decimals of accuracy

so the main problem is Im getting NO INFORMATION from inwerter..

From the watchPower my logs:

QPIRI
[2023-07-11 20:42:47](230.0 04.3 230.0 50.0 04.3 1000 1000 12.0 11.5 10.5 14.1 13.5 2 10 10 0 2 2 - 01 1 0 13.5 0 0
[2023-07-11 20:42:48](230.0 04.3 230.0 50.0 04.3 1000 1000 12.0 11.5 10.5 14.1 13.5 2 10 10 0 2 2 - 01 1 0 13.5 0 0
[2023-07-11 20:42:52](230.0 04.3 230.0 50.0 04.3 1000 1000 12.0 11.5 10.5 14.1 13.5 2 10 10 0 2 2 - 01 1 0 13.5 0 0
[2023-07-11 20:42:53](230.0 04.3 230.0 50.0 04.3 1000 1000 12.0 11.5 10.5 14.1 13.5 2 10 10 0 2 2 - 01 1 0 13.5 0 0
[2023-07-11 20:42:58](230.0 04.3 230.0 50.0 04.3 1000 1000 12.0 11.5 10.5 14.1 13.5 2 10 10 0 2 2 - 01 1 0 13.5 0 0

QPIGS:
[2023-07-11 20:42:49](001.0 00.0 228.0 50.0 0000 0000 000 379 12.42 000 086 0581 0000 000.0 00.00 00001 10010000 00 03 00000 000
[2023-07-11 20:42:52](001.0 00.0 228.0 50.0 0000 0000 000 379 12.42 000 086 0579 0000 000.0 00.00 00001 10010000 00 03 00000 000
[2023-07-11 20:42:54](001.0 00.0 228.0 50.0 0000 0000 000 378 12.42 000 086 0581 0000 000.0 00.00 00001 10010000 00 03 00000 000
[2023-07-11 20:42:57](001.0 00.0 229.0 50.0 0000 0000 000 379 12.42 000 086 0581 0000 000.0 00.00 00001 10010000 00 03 00000 000
[2023-07-11 20:43:00](001.0 00.0 229.0 50.0 0000 0000 000 379 12.42 000 086 0580 0000 000.0 00.00 00001 10010000 00 03 00000 000

Could anybody help here?

[syssi]

Could you ask your manufacturer or seller about a protocol description? The meaning of the different fields of the QPIGS/QPIRI responses could be helpful to spot the differences.

[allbeq]

I have received file - attached
ProtocolDesc.docx

[allbeq]

Bump, any chance to help / hints / which piece of code is responsible for that?