Encoder like a analog note #269
Replies: 11 comments 9 replies
-
That would be very good, but the ideal would be that the encoders could be configured as 2 different notes as if they were a button for each direction of rotation and with each pulse that would repeat the note. |
Beta Was this translation helpful? Give feedback.
-
I'm not sure what exactly are you talking about. There are no float values in MIDI protocol. |
Beta Was this translation helpful? Give feedback.
-
Option 1 is now available on master branch. Rotations send the same note with increasing or decreasing velocity, depending on the direction. |
Beta Was this translation helpful? Give feedback.
-
The encoders now support configuration of two notes and the value for that note. There's also single-note repeated mode available which will send the same note+value in each direction, and another mode where one direction sends configured note+value and another direction sends the same note but with value 0. |
Beta Was this translation helpful? Give feedback.
-
Thanks igor.
I'm going to check it.
El mar, 16 abr 2024, 14:28, paradajz ***@***.***> escribió:
… The encoders now support configuration of two notes and the value for that
note. There's also single-note repeated mode available which will send the
same note+value in each direction, and another mode where one direction
sends configured note+value and another direction sends the same note but
with value 0.
—
Reply to this email directly, view it on GitHub
<#269 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AUX2XQEVNYKOJN5FG67KH3LY5UKPJAVCNFSM6AAAAABDAHZ2MOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TCMRZGY3DE>
.
You are receiving this because you authored the thread.Message ID:
***@***.***
com>
|
Beta Was this translation helpful? Give feedback.
-
Hi Igor,
I have doubts.
The updated firmware is version7.9.0? This is the last firmware in the
releases page. Because I don't be sure...I have updated the board to test
anyway.
In the web configurator...I have tested the "Two note" but it works like
"Single Note/ variable value"
Besides, how can I configure the note for cw and note for ccw?
[image: image.png]
And I have a question. Do you have a board to test? Maybe we can send you
one in case that you don't have any.
El mar, 16 abr 2024 a las 18:07, Pablo Gimeno ***@***.***>)
escribió:
… Thanks igor.
I'm going to check it.
El mar, 16 abr 2024, 14:28, paradajz ***@***.***> escribió:
> The encoders now support configuration of two notes and the value for
> that note. There's also single-note repeated mode available which will send
> the same note+value in each direction, and another mode where one direction
> sends configured note+value and another direction sends the same note but
> with value 0.
>
> —
> Reply to this email directly, view it on GitHub
> <#269 (comment)>,
> or unsubscribe
> <https://github.com/notifications/unsubscribe-auth/AUX2XQEVNYKOJN5FG67KH3LY5UKPJAVCNFSM6AAAAABDAHZ2MOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TCMRZGY3DE>
> .
> You are receiving this because you authored the thread.Message ID:
> ***@***.***
> com>
>
|
Beta Was this translation helpful? Give feedback.
-
The firmware is not released yet. The code is on the master branch so you'd need to compile it. |
Beta Was this translation helpful? Give feedback.
-
Hi,
Then, I must execute the docker and follow the procedure, isn't it?
Take in mind that I don't be an expert user in Linux...
El mié, 17 abr 2024, 14:47, paradajz ***@***.***> escribió:
… The firmware is not released yet. The code is on the master branch so
you'd need to compile it.
—
Reply to this email directly, view it on GitHub
<#269 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AUX2XQATWKAZEHUQ4QF6KY3Y5ZVPXAVCNFSM6AAAAABDAHZ2MOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TCNBSGY2TE>
.
You are receiving this because you authored the thread.Message ID:
***@***.***
com>
|
Beta Was this translation helpful? Give feedback.
-
I've attached both sysex and uf2 firmware variants for the 3.1 board. |
Beta Was this translation helpful? Give feedback.
-
Hi,
Finally I can made the firmware. It works fine!!!
Many thanks!!!
I'm going to test more to be ensure about the functionality.
We'll be in contact. We have more ideas to develop the firmware.
It could be a win win future!!!
El mié, 17 abr 2024, 19:53, paradajz ***@***.***> escribió:
… opendeck31.zip
<https://github.com/shanteacontrols/OpenDeck/files/15015301/opendeck31.zip>
I've attached both sysex and uf2 firmware variants for the 3.1 board.
—
Reply to this email directly, view it on GitHub
<#269 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AUX2XQAP4YL3XL3KCWJW2BLY52ZJJAVCNFSM6AAAAABDAHZ2MOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TCNBWGE3TI>
.
You are receiving this because you authored the thread.Message ID:
***@***.***
com>
|
Beta Was this translation helpful? Give feedback.
-
Glad it works out for you. Released as a part of the new firmare, v7.10.0: |
Beta Was this translation helpful? Give feedback.
-
Hi paradajz,
I see that in the fader configuración, you can send a note on with floating value.
In encoders, you can send an incremental cc.
A good feature will be send the incremental value for the encoders like a floating note value between 0.00 and 1.00.
What do you think? I suppose that only needs a change in the midi packet header value.
Thanks!!
Beta Was this translation helpful? Give feedback.
All reactions