Proxmox setup for OpenVPN and Wireguard

[bnhf]

Mostly good news here, which is that Gluetun can be setup in a Proxmox LXC container using either OpenVPN or Wireguard.

For those familiar with Proxmox, it's the typical steps of creating a container with the latest Debian template (recommended). Before you start the container follow the tweaks in this guide from Proxmox (just those from the attached image if you're using the Proxmox WebUI for everything else). Substitute your container ID for the "123" used in the example:

https://pve.proxmox.com/wiki/OpenVPN_in_LXC

Then you'll need to install Docker for sure, but if you're like me you'll want to add a few other favorites (Portainer, Cockpit, Cockpit-Navigator and Organizr in my case). You might want to turn this container into a template at this point for future similar projects, and continue on with a clone.

Your standard Gluetun Stack should work, with the addition of (assuming you don't normally use it):

    devices:
      - /dev/net/tun:/dev/net/tun

Performance is excellent with OpenVPN as it uses the kernelspace implementation. Wireguard is good too, though for some reason it falls back to the userspace version of Wireguard. Which brings me to my question:

Anybody figured out how to get Wireguard to use its kernelspace capability with a Proxmox setup like this?

Pretty similar OpenVPN performance to what I see using Docker running on a bare metal install of Debian:

[dhenry437]

Pretty much the same set up as you, although no idea whether Wireguard is failing back to the userspace version (don't know how to check). But I am getting slightly faster speeds compared to baseline with OpenVPN. Is this due to kernel vs userspace? From what I've read I thought it was meant to be the other way around?

[chenks]

@bnhf @dhenry437 just followed your instructions and the gluetun container is still failing to create with the error error gathering device information while adding custom device "/dev/net/tun": no such file or directory

i added this to the conf file

lxc.cgroup2.devices.allow: c 10:200 rwm
lxc.mount.entry: /dev/net /dev/net none bind,create=dir

and this is the permissions check

root@proxmox:~# ls -l /dev/net/tun
crw-rw-rw- 1 root root 10, 200 May 21 13:07 /dev/net/tun

any ideas? proxmox 8.2.2 with the LXC being a deb12 template.

[dhenry437]

From the Gluetun wiki the bit added to the conf file should be:

lxc.cgroup2.devices.allow: c 10:200 rwm
lxc.mount.entry: /dev/net dev/net none bind,create=dir
lxc.mount.entry: /dev/net/tun dev/net/tun none bind,create=file

But I do remember getting an error along those lines and not having

devices:
  - /dev/net/tun:/dev/net/tun

in the docker-compose was the issue.

Although even after getting this set up and working, I found the speed in qBit was fluctuating a lot. So I've since switched to hotio's qBit container that has VPN built in. Much easier to set up and more stable for me. I don't know what you're using this for but if its qBit you could try that.

[chenks]

i route a few things thru gluetun, so not just qbittorrent

i already have this in the docker-compose file

devices:
  - /dev/net/tun:/dev/net/tun

i was following the screenshot in the original so wasn't aware that lxc.mount.entry: /dev/net/tun dev/net/tun none bind,create=file wa also required, i will try that now.

[chenks]

this is now working, was that missing line in the conf

[anton-dealmeida]

Thanks a lot for this thread!