Skip to content

Latest commit

 

History

History
106 lines (68 loc) · 4.82 KB

README.md

File metadata and controls

106 lines (68 loc) · 4.82 KB
Raw

QT Py DIY Temperature Sensor

Step-by-step instructions and code for a DIY temperature sensor using a QT Py with pictures

Table of contents

Technologies

Project is created with:

  • CircuitPython (6.1.0)

Parts:

Optional (for temperature probe)

  • 4x long jumper cables
  • Tape
  • Heat shrink
  • Hot glue (NOT RECOMENDED)

Setup / Prerequisite installations

Follow these instructions to set up you QT Py or go to the following link: https://learn.adafruit.com/adafruit-qt-py/overview

To start, go to https://circuitpython.org/board/qtpy_m0/ to download the latest version of CircuitPython.

Download and save it to your desktop (or wherever is handy).

Plug your QT Py into your computer using a known-good USB cable.

A lot of people end up using charge-only USB cables and it is very frustrating! So make sure you have a USB cable you know is good for data sync.

Double-click the small RST (reset) button, and you will see the NeoPixel RGB LED turn green. If it turns red, check the USB cable, try another USB port, etc.

If double-clicking doesn't work the first time, try again. Sometimes it can take a few tries to get the rhythm right!

You will see a new disk drive appear called QTPY_BOOT.

Drag the adafruit_circuitpython_etc.uf2 file to QTPY_BOOT. The red LED will flash. Then, the QTPY_BOOT drive will disappear and a new disk drive called CIRCUITPY will appear.

Installing MU Editor (Highly seggested)

Mu is a simple code editor that works with the Adafruit CircuitPython boards. It's written in Python and works on Windows, MacOS, Linux and Raspberry Pi. The serial console is built right in so you get immediate feedback from your board's serial output!

if you already have a favorite IDE use that one because MU edotor is not the best IDE but it has the serial console built right in so at least use it for that.

Programing your QT Py

Go into the IDE that you are using and create a python file in your CIRCUITPY directory. name the file code.py

You can now program in python and you are going to have to google the special things you can do with this board because I am not writing it here.

My code: code.py

To run your code simply save it or hit the reset button. Any print() functions will show up on your serial console (in MU editor)

The Circuit

Setting up the OLED display

First thing you need to do is download this file onto any convenient folder (I just used my downloads folder).

adafruit-circuitpython-bundle-6.x-mpy-20210321.zip

This is a ZIP file that contains many CircuitPython libraries, some of which we will need to copy onto the CIRCUITPY directory. Unzip the file.

For people with the optional solderable flash chip:

For you it is very easy all you have to do is:

  1. Go into the new folder that was just created when you unzipped the file
  2. Go into the lib folder
  3. Find adafruit_displayio_ssd1306.mpy and adafruit_bus_device folders
  4. Copy them into the lib folder of your CIRCUITPY
  5. Google ways to program it and copy in any aditional libraries called for

For the people without the optional solderable chip (What I had):

This is where it gets tricky and I had to do a lot of reaserch and trial and error. I can't find any source that actualy had a working version of this, but I came up with this solution:

  1. Go into the new folder that was just created when you unzipped the file
  2. Go into the lib folder
  3. Find the folder adafruit_bus_device
  4. Copy that into the lib folder of your CIRCUITPY directory
  5. Also find and copy adafruit_framebuf.mpy and adafruit_ssd1306.mpy into your lib folder
  6. Next, go back the the unzipped folder and into examples
  7. Find font5x8.bin
  8. Copy this into your CIRCUITPY (outside the lib folder)

You will only be able to display text but the other libraries take too much space that you don't have because you don't have the optional flash chip.

My code (comments where there is something for the display): code.py