usbd_conf.c

/**
  ******************************************************************************
  * @file    umart_lite_plus_teste/src/usbd_conf.c
  * @author  MCD Application Team
  * @version V1.2.0
  * @date    26-December-2014
  * @brief   This file implements the USB Device library callbacks and MSP
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  ******************************************************************************
  * @remark
  * Funções HAL_PCD_MspInit, HAL_PCD_MspDeInit e USBD_LL_Init modificadas por
  * Kleber Lima da Silva (kleber.ufu@hotmail.com) em 26-Abril-2015
  *
  */

/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_hal.h"
#include "usbd_core.h"


/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
PCD_HandleTypeDef hpcd;

/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/

/*******************************************************************************
                       PCD BSP Routines
*******************************************************************************/
/**
  * @brief  Initializes the PCD MSP.
  * @param  hpcd: PCD handle
  * @retval None
  */
void HAL_PCD_MspInit(PCD_HandleTypeDef *hpcd)
{
  GPIO_InitTypeDef  GPIO_InitStruct;
  
  if(hpcd->Instance == USB_OTG_FS)
  {
    /* Configure USB FS GPIOs */

	__GPIOA_CLK_ENABLE();
    
    /* Configure DM DP Pins */
    GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
    GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); 
    
	/* Configure VBUS Pin */
    /*GPIO_InitStruct.Pin = GPIO_PIN_9;
    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);*/
	
    /* Configure ID pin */
    /*GPIO_InitStruct.Pin = GPIO_PIN_10;
    GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);*/

    /* Enable USB FS Clocks */
    __USB_OTG_FS_CLK_ENABLE();
    
    /* Set USBFS Interrupt priority */
    HAL_NVIC_SetPriority(OTG_FS_IRQn, 6, 0);
    
    /* Enable USBFS Interrupt */
    HAL_NVIC_EnableIRQ(OTG_FS_IRQn);
  }
}
/**
  * @brief  DeInitializes the PCD MSP.
  * @param  hpcd: PCD handle
  * @retval None
  */
void HAL_PCD_MspDeInit(PCD_HandleTypeDef *hpcd)
{
  if(hpcd->Instance == USB_OTG_FS)
  {  
    /* Disable USB FS Clocks */ 
	  __USB_OTG_FS_CLK_DISABLE();
	  __SYSCFG_CLK_DISABLE();
  }
}

/*******************************************************************************
                       LL Driver Callbacks (PCD -> USB Device Library)
*******************************************************************************/


/**
  * @brief  Setup stage callback.
  * @param  hpcd: PCD handle
  * @retval None
  */
void HAL_PCD_SetupStageCallback(PCD_HandleTypeDef *hpcd)
{
  USBD_LL_SetupStage(hpcd->pData, (uint8_t *)hpcd->Setup);
}

/**
  * @brief  Data Out stage callback.
  * @param  hpcd: PCD handle
  * @param  epnum: Endpoint Number
  * @retval None
  */
void HAL_PCD_DataOutStageCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum)
{
  USBD_LL_DataOutStage(hpcd->pData, epnum, hpcd->OUT_ep[epnum].xfer_buff);
}

/**
  * @brief  Data In stage callback.
  * @param  hpcd: PCD handle
  * @param  epnum: Endpoint Number
  * @retval None
  */
void HAL_PCD_DataInStageCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum)
{
  USBD_LL_DataInStage(hpcd->pData, epnum, hpcd->IN_ep[epnum].xfer_buff);
}

/**
  * @brief  SOF callback.
  * @param  hpcd: PCD handle
  * @retval None
  */
void HAL_PCD_SOFCallback(PCD_HandleTypeDef *hpcd)
{
  USBD_LL_SOF(hpcd->pData);
}

/**
  * @brief  Reset callback.
  * @param  hpcd: PCD handle
  * @retval None
  */
void HAL_PCD_ResetCallback(PCD_HandleTypeDef *hpcd)
{ 
  USBD_SpeedTypeDef speed = USBD_SPEED_FULL;

  /* Set USB Current Speed */
  switch(hpcd->Init.speed)
  {
  case PCD_SPEED_HIGH:
    speed = USBD_SPEED_HIGH;
    break;
    
  case PCD_SPEED_FULL:
    speed = USBD_SPEED_FULL;    
    break;
	
	default:
    speed = USBD_SPEED_FULL;    
    break;
  }
  USBD_LL_SetSpeed(hpcd->pData, speed);  
  
  /* Reset Device */
  USBD_LL_Reset(hpcd->pData);
}

/**
  * @brief  Suspend callback.
  * @param  hpcd: PCD handle
  * @retval None
  */
void HAL_PCD_SuspendCallback(PCD_HandleTypeDef *hpcd)
{
  USBD_LL_Suspend(hpcd->pData);
}

/**
  * @brief  Resume callback.
  * @param  hpcd: PCD handle
  * @retval None
  */
void HAL_PCD_ResumeCallback(PCD_HandleTypeDef *hpcd)
{
  USBD_LL_Resume(hpcd->pData);
}

/**
  * @brief  ISOC Out Incomplete callback.
  * @param  hpcd: PCD handle
  * @param  epnum: Endpoint Number  
  * @retval None
  */
void HAL_PCD_ISOOUTIncompleteCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum)
{
  USBD_LL_IsoOUTIncomplete(hpcd->pData, epnum);
}

/**
  * @brief  ISOC In Incomplete callback.
  * @param  hpcd: PCD handle
  * @param  epnum: Endpoint Number  
  * @retval None
  */
void HAL_PCD_ISOINIncompleteCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum)
{
  USBD_LL_IsoINIncomplete(hpcd->pData, epnum);
}

/**
  * @brief  Connect callback.
  * @param  hpcd: PCD handle
  * @retval None
  */
void HAL_PCD_ConnectCallback(PCD_HandleTypeDef *hpcd)
{
  USBD_LL_DevConnected(hpcd->pData);
}

/**
  * @brief  Disconnect callback.
  * @param  hpcd: PCD handle
  * @retval None
  */
void HAL_PCD_DisconnectCallback(PCD_HandleTypeDef *hpcd)
{
  USBD_LL_DevDisconnected(hpcd->pData);
}

/*******************************************************************************
                       LL Driver Interface (USB Device Library --> PCD)
*******************************************************************************/
/**
  * @brief  Initializes the Low Level portion of the Device driver.  
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef  USBD_LL_Init (USBD_HandleTypeDef *pdev)
{ 
  /* Change Systick prioity */
  NVIC_SetPriority (SysTick_IRQn, 0);  
  
  /*Set LL Driver parameters */
  hpcd.Instance = USB_OTG_FS;
  hpcd.Init.dev_endpoints = 4; 
  hpcd.Init.use_dedicated_ep1 = 0;
  hpcd.Init.ep0_mps = 0x40;  
  hpcd.Init.dma_enable = 0;
  hpcd.Init.low_power_enable = 0;
  hpcd.Init.phy_itface = PCD_PHY_EMBEDDED; 
  hpcd.Init.Sof_enable = 0;
  hpcd.Init.speed = PCD_SPEED_FULL;
  hpcd.Init.vbus_sensing_enable = 1;
  /* Link The driver to the stack */
  hpcd.pData = pdev;
  pdev->pData = &hpcd;
  /*Initialize LL Driver */
  HAL_PCD_Init(&hpcd);
  
  HAL_PCDEx_SetRxFiFo(&hpcd, 0x80);
  HAL_PCDEx_SetTxFiFo(&hpcd, 0, 0x40);
  HAL_PCDEx_SetTxFiFo(&hpcd, 1, 0x80); 

  return USBD_OK;
}

/**
  * @brief  De-Initializes the Low Level portion of the Device driver. 
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_DeInit(USBD_HandleTypeDef *pdev)
{
  HAL_PCD_DeInit(pdev->pData);
  return USBD_OK; 
}

/**
  * @brief  Starts the Low Level portion of the Device driver.    
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_Start(USBD_HandleTypeDef *pdev)
{
  HAL_PCD_Start(pdev->pData);
  return USBD_OK; 
}

/**
  * @brief  Stops the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_Stop(USBD_HandleTypeDef *pdev)
{
  HAL_PCD_Stop(pdev->pData);
  return USBD_OK; 
}

/**
  * @brief  Opens an endpoint of the Low Level Driver. 
  * @param  pdev: Device handle
  * @param  ep_addr: Endpoint Number
  * @param  ep_type: Endpoint Type
  * @param  ep_mps: Endpoint Max Packet Size                 
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_OpenEP(USBD_HandleTypeDef *pdev, 
                                  uint8_t  ep_addr,                                      
                                  uint8_t  ep_type,
                                  uint16_t ep_mps)
{
  HAL_PCD_EP_Open(pdev->pData, ep_addr, ep_mps, ep_type);
  return USBD_OK; 
}

/**
  * @brief  Closes an endpoint of the Low Level Driver.  
  * @param  pdev: Device handle
  * @param  ep_addr: Endpoint Number      
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_CloseEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr)   
{
  HAL_PCD_EP_Close(pdev->pData, ep_addr);
  return USBD_OK; 
}

/**
  * @brief  Flushes an endpoint of the Low Level Driver.
  * @param  pdev: Device handle
  * @param  ep_addr: Endpoint Number      
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_FlushEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr)   
{
  HAL_PCD_EP_Flush(pdev->pData, ep_addr);
  return USBD_OK; 
}

/**
  * @brief  Sets a Stall condition on an endpoint of the Low Level Driver.
  * @param  pdev: Device handle
  * @param  ep_addr: Endpoint Number      
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_StallEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr)   
{
  HAL_PCD_EP_SetStall(pdev->pData, ep_addr);
  return USBD_OK; 
}

/**
  * @brief  Clears a Stall condition on an endpoint of the Low Level Driver.
  * @param  pdev: Device handle
  * @param  ep_addr: Endpoint Number      
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_ClearStallEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr)   
{
  HAL_PCD_EP_ClrStall(pdev->pData, ep_addr);  
  return USBD_OK; 
}

/**
  * @brief  Returns Stall condition.
  * @param  pdev: Device handle
  * @param  ep_addr: Endpoint Number      
  * @retval Stall (1: yes, 0: No)
  */
uint8_t USBD_LL_IsStallEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr)   
{
  PCD_HandleTypeDef *hpcd = pdev->pData; 
  
  if((ep_addr & 0x80) == 0x80)
  {
    return hpcd->IN_ep[ep_addr & 0x7F].is_stall; 
  }
  else
  {
    return hpcd->OUT_ep[ep_addr & 0x7F].is_stall; 
  }
}

/**
  * @brief  Assigns an USB address to the device
  * @param  pdev: Device handle
  * @param  dev_addr: USB address      
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_SetUSBAddress(USBD_HandleTypeDef *pdev, uint8_t dev_addr)   
{
  HAL_PCD_SetAddress(pdev->pData, dev_addr);
  return USBD_OK; 
}

/**
  * @brief  Transmits data over an endpoint 
  * @param  pdev: Device handle
  * @param  ep_addr: Endpoint Number
  * @param  pbuf: Pointer to data to be sent    
  * @param  size: Data size    
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_Transmit(USBD_HandleTypeDef *pdev, 
                                    uint8_t  ep_addr,                                      
                                    uint8_t  *pbuf,
                                    uint16_t  size)
{
  HAL_PCD_EP_Transmit(pdev->pData, ep_addr, pbuf, size);
  return USBD_OK;   
}

/**
  * @brief  Prepares an endpoint for reception 
  * @param  pdev: Device handle
  * @param  ep_addr: Endpoint Number
  * @param  pbuf:pointer to data to be received    
  * @param  size: data size              
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_PrepareReceive(USBD_HandleTypeDef *pdev, 
                                          uint8_t  ep_addr,                                      
                                          uint8_t  *pbuf,
                                          uint16_t  size)
{
  HAL_PCD_EP_Receive(pdev->pData, ep_addr, pbuf, size);
  return USBD_OK;   
}

/**
  * @brief  Returns the last transfered packet size.    
  * @param  pdev: Device handle
  * @param  ep_addr: Endpoint Number
  * @retval Recived Data Size
  */
uint32_t USBD_LL_GetRxDataSize(USBD_HandleTypeDef *pdev, uint8_t  ep_addr)  
{
  return HAL_PCD_EP_GetRxCount(pdev->pData, ep_addr);
}

/**
  * @brief  Delay routine for the USB Device Library      
  * @param  Delay: Delay in ms
  * @retval None
  */
void  USBD_LL_Delay(uint32_t Delay)
{
  HAL_Delay(Delay);  
}

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/