Skip to content

Latest commit

 

History

History
258 lines (204 loc) · 13.4 KB

CAR INSTALL.md

File metadata and controls

258 lines (204 loc) · 13.4 KB

Shairport Sync for Cars

If your car audio has an AUX input, you can get AirPlay in your car using Shairport Sync. Together, Shairport Sync and an iPhone can give you access to internet radio, YouTube, Apple Music, Spotify, etc. on the move. While Shairport Sync is no substitute for CarPlay, the audio quality is often much better than Bluetooth. Your passengers can enjoy movies with the soundtrack on the car speakers.

The Basic Idea

The basic idea is to use a small Linux computer to create an isolated WiFi network for the car and to run Shairport Sync on it to provide an AirPlay service. The audio goes via a DAC to the AUX input of your car audio system.

The car WiFi network you create is isolated and local to your car, and since it isn't connected to the Internet, you don't really need to secure it with a password. Likewise, you don't really have to use a password to connect to the AirPlay service.

When an iPhone or an iPad with cellular capability is connected to an isolated WiFi network like this, it can use its cellular connection to access the Internet. This means it can connect to internet radio, YouTube, Apple Music, Spotify, etc. over the cellular network and play the audio through the car network to the AirPlay service provided by Shairport Sync.

Note that Android devices can not, so far, do this trick of using the two networks simultaneously.

Example

In this example, a Raspberry Pi Zero W and a Pimoroni PHAT DAC are used. This combination has been tested for over two years. Please note that some of the details of setting up networks are specific to the version of Linux used -- Raspbian Stretch or later.

Prepare the initial SD Image

  • Download the latest version of Raspbian Lite -- Stretch Lite of 2018-03-13 at the time of writing -- and install it onto an SD Card.
  • Mount the card on a Linux machine. Two drives should appear -- a boot drive and a rootfs drive. Both of these need a little modification.
  • Enable SSH service by creating a file called ssh on the boot drive. To do this, mount the drive and CD to its boot partition (since my username is mike, the drive is at /media/mike/boot):
$ touch ssh
  • Also in the boot drive, edit the config.txt file to add the overlay needed for the sound card. This may not be necessary in your case, but in this example a Pimoroni PHAT is being used and it needs the following entry to be added:
dtoverlay=hifiberry-dac
  • Next, some modifications need to be done to the rootfs drive to make the Pi connect to your main WiFi network. (This is a temporary measure to enable you to connect the Pi to your main network so that you can do all the software installation and updating of the software necessary. Later, the Pi will be configured to start its own isolated network.) On the rootfs drive, edit the file etc/wpa_supplicant/wpa_supplicant.conf (you'll need root privileges) and add the name and password of your main WiFi network (substitute your own network name and password in, but keep the quotation marks):
network={
    ssid="Network Name"
    psk="Password"
}

Close the file and carefully dismount and eject the two drives. Remove the SD card from the Linux machine, insert it into the Pi and reboot. After a short time, the Pi should appear on your network and you can SSH into it. To check that it has appeared on the network, try to ping it at raspberrypi.local. It may take a minute or so to appear. Once it has appeared on your network you can SSH into it and configure it.

Boot, Configure, Update

The first thing to do on a Pi would be to use the raspi-config tool to expand the file system to use the entire card. It might be useful to change the hostname too. Next, do the usual update and upgrade:

# apt-get update
# apt-get upgrade

Shairport Sync

First, install the packages needed by Shairport Sync:

# apt-get install build-essential git xmltoman autoconf automake libtool libpopt-dev libconfig-dev libasound2-dev avahi-daemon libavahi-client-dev libssl-dev libsoxr-dev

Next, download Shairport Sync, configure it, compile and install it:

$ git clone https://github.com/mikebrady/shairport-sync.git
$ cd shairport-sync
$ autoreconf -fi
$ ./configure --sysconfdir=/etc --with-alsa --with-avahi --with-ssl=openssl --with-soxr --with-systemd
$ make
$ sudo make install

Do not enable Shairport Sync to automatically start at boot time -- startup is organised differently.

Third, finish by configuring Shairport Sync. Here are the important options for the Shairport Sync configuration file at /etc/shairport-sync.conf:

// Sample Configuration File for Shairport Sync for Car Audio with a Pimoroni PHAT
general =
{
	name = "BMW Radio";
	ignore_volume_control = "yes";
	volume_max_db = -3.00;
};

alsa =
{
	output_device = "hw:1"; // the name of the alsa output device. Use "alsamixer" or "aplay" to find out the names of devices, mixers, etc.
};

Two general settings are worth noting. First, the option to ignore the sending device's volume control is enabled -- this means that the car audio's volume control is the only one that affects the audio volume. Of course this is a matter of personal preference. Second, the maximum output offered by the DAC to the AUX port of the car audio can be reduced if it is overloading the input circuits. Again, that's a matter for personal selection and adjustment.

The alsa settings are for the Pimoroni PHAT -- it does not have a hardware mixer, so no mixer_control_name is given.

Note that the DAC's 32-bit capability is automatically selected if available, so there is no need to set it here. Similarly, since soxr support is included in the build, soxr interpolation will be automatically enabled if the device is fast enough.

Extra Packages

A number of packages to enable the Pi to work as a WiFi base station are needed:

# apt-get install hostapd isc-dhcp-server

Disable both of these services from starting at boot time (this is because we will launch them sequentially later on):

# systemctl unmask hostapd
# systemctl disable hostapd
# systemctl disable isc-dhcp-server

Configure HostAPD

Configure hostapd by creating /etc/hostapd/hostapd.conf with the following contents which will set up an open network with the name BMW. You might wish to change the name:

# This is the name of the WiFi interface we configured above
interface=wlan0

# Use the nl80211 driver with the brcmfmac driver
driver=nl80211

# This is the name of the network -- yours might be different
ssid=BMW

# Use the 2.4GHz band
hw_mode=g

# Use channel 6
channel=9

# Enable 802.11n
ieee80211n=1

# Enable WMM
wmm_enabled=1

# Enable 40MHz channels with 20ns guard interval
#ht_capab=[HT40][SHORT-GI-20][DSSS_CCK-40]

# Accept all MAC addresses
macaddr_acl=0

# Use WPA authentication
#auth_algs=1

# Require clients to know the network name
ignore_broadcast_ssid=0

# Use WPA2
#wpa=2

# Use a pre-shared key
#wpa_key_mgmt=WPA-PSK

# The network passphrase
#wpa_passphrase=none

# Use AES, instead of TKIP
#rsn_pairwise=CCMP

Configure DHCP server

First, replace the contents of /etc/dhcp/dhcpd.conf with this:

subnet 10.0.10.0 netmask 255.255.255.0 {
     range 10.0.10.5 10.0.10.150;
     #option routers <the-IP-address-of-your-gateway-or-router>;
     #option broadcast-address <the-broadcast-IP-address-for-your-network>;
}

Second, modify the INTERFACESv4 entry at the end of the file /etc/default/isc-dhcp-server to look as follows:

INTERFACESv4="wlan0"
INTERFACESv6=""

Set up the Startup Sequence

Configure the startup sequence by adding commands to /etc/rc.local to start hostapd and the dhcp server and then to start shairport-sync automatically after startup. Its contents should look like this:

#!/bin/sh -e
#
# rc.local
#
# This script is executed at the end of each multiuser runlevel.
# Make sure that the script will "exit 0" on success or any other
# value on error.
#
# In order to enable or disable this script just change the execution
# bits.
#
# By default this script does nothing.

/sbin/iw dev wlan0 set power_save off
/usr/sbin/hostapd -B -P /run/hostapd.pid /etc/hostapd/hostapd.conf
/sbin/ip addr add 10.0.10.1/24 dev wlan0
/bin/sleep 1
/bin/systemctl start isc-dhcp-server
/bin/sleep 2
/bin/systemctl start shairport-sync

exit 0

As you can see, the effect of these commands is to start the WiFi transmitter, give the base station the IP address 10.0.10.1, start a DHCP server and finally start the Shairport Sync service.

Final Steps

Up to now, if you reboot the Pi, it will reconnect to your WiFi network, ignoring the instructions and settings you have given it to act as a base station. That is because the wlan0 interface is still under the control of the dhcpcd service. So, the final step is to instruct the dhcpcd service not to manage wlan0. To do this, edit /etc/dhcpcd.conf and insert the following line at the start:

denyinterfaces wlan0

From this point on, at least on the Raspberry Pi, if you reboot the machine, it will not reconnect to your network – instead, it will act as the WiFi base station you have configured with hostapd and isc-dhcp-server.

Optimise startup time -- Raspberry Pi Specific

This is applicable to a Raspberry Pi only. Some of it may be applicable to other systems, but it has not been tested on them. There are quite a few services that are not necessary for this setup. Disabling them can shorten startup time. Running these commands disables them:

sudo systemctl disable systemd-timesyncd.service
sudo systemctl disable keyboard-setup.service
sudo systemctl disable triggerhappy.service
sudo systemctl disable dhcpcd.service
sudo systemctl disable wpa_supplicant.service
sudo systemctl disable dphys-swapfile.service
sudo systemctl disable networking.service

Read-only mode -- Raspberry Pi Specific

Run sudo raspi-config and then choose Performance Options > Overlay Filesystem and choose to enable the overlay filesystem, and to set the boot partition to be write-protected.

Ready

Install the Raspberry Pi in your car. It should be powered from a source that is switched off when you leave the car, otherwise the slight current drain will eventually flatten the car's battery.

When the power source is switched on, typically when you start the car, it will take maybe a minute for the system to boot up.

Enjoy!


Updating

From time to time, you may wish to update this installation. However, in order to update Shairport Sync, you must reconnect the system to a network that can access the internet. The easiest thing is to temporarily reconnect to the network you used when you created the system. To do that, you have to temporarily undo the "Final Steps" and some of the "Raspberry Pi Specific" steps you used. This will enable you to connect your device back to the network it was created on. You should then be able to update the operating system and libraries in the normal way and then update Shairport Sync.

So, take the following steps:

  1. If it's a Raspberry Pi and you have enabled the Read-only mode, you must take the device out of Read-only mode:
    Run sudo raspi-config and then choose Performance Options > Overlay Filesystem and choose to disable the overlay filesystem and to set the boot partition not to be write-protected. This is so that changes can be written to the file system; you can make the filesystem read-only again later. Save the changes and reboot the system.

  2. If you have disabled the dhcpcd, wpa_supplicant or systemd-timesyncd services as suggested in the "Optimise startup time -- Raspberry Pi Specific" section, you need to temporarily re-enable them:
    # systemctl enable dhcpcd.service
    # systemctl enable wpa_supplicant.service
    # systemctl enable systemd-timesyncd.service
    Reboot.

  3. To allow your device to reconnect to the network it was created on, edit /etc/dhcpcd.conf and comment out the following line at the start:
    denyinterfaces wlan0
    so that it looks like this:
    # denyinterfaces wlan0
    From this point on, if you reboot the machine, it will connect to the network it was configured on, i.e. the network you used when you set it up for the first time. This is because the name and password of the network it was created on would have been placed in /etc/wpa_supplicant/wpa_supplicant when the system was initially configured and will still be there.

  4. Reboot and do Normal Updating

    You can perform updates in the normal way -- see UPDATING. When you are finished, you need to undo the temporary changes you made to the setup, as follows:

  5. If you had temporarily re-enabled services that are normally disabled, then it's time to disable them again:
    # systemctl disable dhcpcd.service
    # systemctl disable wpa_supplicant.service
    # systemctl disable systemd-timesyncd.service

  6. To re-enable the system to create its own network, edit /etc/dhcpcd.conf and uncomment the line that you had temporarily commented out at the start of the update. Change:
    # denyinterfaces wlan0
    so that it looks like this:
    denyinterfaces wlan0

  7. Reboot. The system should start as it would if it was in the car.

  8. If the device is a Raspberry Pi and you wish to make the file system read-only, connect to the system, run sudo raspi-config and then choose Performance Options > Overlay Filesystem. In there, choose to enable the overlay filesystem, and to set the boot partition to be write-protected. Do a final reboot and check that everyting is in order.