-
Notifications
You must be signed in to change notification settings - Fork 20
/
Rascal110-Electric-YASim.xml
142 lines (114 loc) · 4.91 KB
/
Rascal110-Electric-YASim.xml
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
<?xml version="1.0"?>
<!--
************************************************************************
YASim aerodynamic model for a Rascal 110 (R/C airplane by Sig Mfg.)
Started December 19, 2005 by Curtis Olson.
This aerodynamic model is based on three-views, self captured
performance data, and few guesses. These sites provided particularly
useful information or were simply fun to visit:
http://gallinazo.flightgear.org/uas/rascal-1/sig-rascal-110-1-construction/
The reference datum for measurements is the tip of the nose.
************************************************************************
-->
<!-- 12 lb aircraft weight includes engine, but not fuel (empty weight) -->
<airplane version="YASIM_VERSION_CURRENT" mass-kg="5.4" mtow-kg="25">
<!-- Approach configuration -->
<approach speed="18" aoa="4">
<control-setting axis="/controls/engines/engine[0]/throttle" value="0.10"/>
</approach>
<!-- Cruise configuration -->
<cruise speed="30" alt="1000">
<control-setting axis="/controls/engines/engine[0]/throttle" value="1.00"/>
<control-setting axis="/controls/engines/engine[0]/mixture" value="1.00"/>
<control-setting axis="/controls/flight/elevator-trim" value="0.4"/>
</cruise>
<!-- pilot's eyepoint -->
<cockpit x="-0.48" y="0" z="0.30"/>
<fuselage ax="0.00" ay="0.00" az="-0.05" bx="-1.93" by="0.00" bz="-0.05"
width="0.30" taper="0.47" midpoint="0.58"/>
<!--
The Rascal has an eliptical wing, but we'll model it as a straight
tapered wing with the equivalent wing area.
Note that the dihedral is exaggerated to simulate hull-interference effects
on a high-wing aircraft; once YASim models that properly, the
angle should be reduced to something like 2 degrees.
Note that the Rascal has no flaps. With a stall speed of 10kt, who
needs them?
-->
<wing x="-0.66" y="0.07" z="0.11" taper="0.73" incidence="0" twist="-3"
length="1.33" chord="0.41" sweep="0" dihedral="5" camber="0.0">
<stall aoa="15" width="4" peak="1.5"/>
<flap0 start="0.40" end="0.95" lift="1.1" drag="1.2"/>
<control-input axis="/controls/flight/aileron" control="FLAP0" split="true"/>
<control-input axis="/controls/flight/aileron-trim" control="FLAP0" split="true"/>
<control-output control="FLAP0" side="left" prop="/surface-positions/left-aileron-pos-norm"/>
<control-output control="FLAP0" side="right" prop="/surface-positions/right-aileron-pos-norm"/>
</wing>
<hstab x="-1.80" y="0.03" z="0.00" taper="0.6" effectiveness="1.0"
length="0.43" chord="0.18" sweep="0" incidence="0.00">
<stall aoa="16" width="4" peak="1.5"/>
<flap0 start="0" end="1" lift="1.3" drag="1.2"/>
<control-input axis="/controls/flight/elevator" control="FLAP0"/>
<control-input axis="/controls/flight/elevator-trim" control="FLAP0"/>
<control-output control="FLAP0" prop="/surface-positions/elevator-pos-norm"/>
</hstab>
<!--
-->
<!-- rudder has to be able to counteract aileron drag -->
<vstab x="-1.80" y="0.00" z="0.00" taper="0.38" effectiveness="1.0"
length="0.37" chord="0.33" sweep="0" incidence="0.00">
<stall aoa="16" width="4" peak="1.5"/>
<flap0 start="0" end="1" lift="2.0" drag="1.2"/>
<control-input axis="/controls/flight/rudder" control="FLAP0" invert="true"/>
<control-input axis="/controls/flight/rudder-trim" control="FLAP0" invert="true"/>
<control-output control="FLAP0" prop="/surface-positions/rudder-pos-norm"
min="1" max="-1"/>
</vstab>
<!-- motor is reported to do 2.4 bhp but this way over powers the aircraft -->
<propeller radius="0.23"
x="-0.10" y="0.00" z="0.00"
mass="3.5" moment="0.001"
cruise-speed="30" cruise-rpm="7000"
cruise-alt="2000" cruise-power="1.3"
takeoff-power="1.5" takeoff-rpm="8000"
contra="0"
>
<actionpt x="0.00" y="0.00" z="0.00"/>
<electric-engine Kv="750" voltage="15" Rm="0.02" >
<control-input axis="/controls/engines/engine[0]/throttle" control="THROTTLE"/>
</electric-engine>
</propeller>
<!-- tail gear -->
<gear x="-1.93" y="0.00" z="-0.13"
sfric="1.6"
dfric="1.3"
compression="0.01"
>
<control-input axis="/controls/flight/rudder" control="STEER"
src0="-1.0" src1="1.0"
dst0="0.5" dst1="-0.5"/>
</gear>
<!-- left main -->
<gear x="-0.48" y="0.27" z="-0.39"
sfric="1.2"
dfric="1.1"
compression="0.03"
>
<control-input axis="/controls/gear/brake-left" control="BRAKE" split="true"/>
<control-input axis="/controls/gear/brake-parking" control="BRAKE" split="true"/>
</gear>
<!-- right main -->
<gear x="-0.48" y="-0.27" z="-0.39"
sfric="1.2"
dfric="1.1"
compression="0.03"
>
<control-input axis="/controls/gear/brake-right" control="BRAKE" split="true"/>
<control-input axis="/controls/gear/brake-parking" control="BRAKE" split="true"/>
</gear>
<!-- There's just one 20 oz tank, right behind the engine (!!!) -->
<tank x="-0.23" y="0.0" z="-0.08" capacity="1.00"/>
<!--
<ballast x="0.0" y="00" z="0.0" mass="1.2"/>
-->
</airplane>